FERROPREP : AC (HEAVY DUTY ELECTROCLEANER FOR STEEL)

FERROPREP: AC is a highly conductive, alkaline, Heavy-Duty anodic for steel. 
In addition to its high capacity for removing a whole variety of soils, Ferroprep: AC is comparatively tolerant to both hard water and to hexavalent chromium. As a result Ferroprep: AC is especially recommended for use in areas where hard water may be encountered.
W hen used under the correct conditions, Ferroprep: AC will produce a bright smut free surface on the steel basis metal. However, as it has been designed for use with heavily soiled polished steel, especially when only light cleaning operations are required lower range of product could be used.

OPERATING CONDITIONS

  OPTIMUM RANGE
FERROPERP: AC 75 g/L 50-100 g/L
TEMPERATURE 90°C (190°F) 85-95°C (185-200°F)
CURRENT DENSITY 5-10 A/dm2 (50-100 A/ft.2) Room
TIME 1-5 minutes  
TANKS AND HEATERS Steel  
ELECTRODES Steel  

MAKEUP PROCEDURE

The tank should be 2/3 filled with water and heated to 60°C (140°F). The required quantity of Ferroprep: AC should then be slowly added with continuous stirring. When dissolved, adjust the solution to the desired volume and heat to the operating temperature.

WASTE DISPOSAL

Solutions of Ferroprep: AC are alkaline. Neutralize to pH 6-8 with an acid and discharge to sewer. Acid must be added slowly and with caution. Wear goggles and protective clothing.

CAUTION

Ferroprep: AC is highly alkaline. Protect eyes with goggles and wear protective clothing. Avoid eye and skin contact. Flush exposed areas immediately with cold water. Call a doctor in case of injury.

top
 

[/toggle]

Metaprep : HSC

METAPREP : HSC (MULTIPURPOSE ALKALINE HEAVY SOAK CLEANER)

Ronuk Metaprep H.S.C. is a high – efficiency, multipurpose alkaline heavy duty soak cleaner designed for use wherever a large variety of SOILS on metals must be processed. Oils, greases, waxy drawing compounds, buffing residues, sulphurized and chlorinated oils, and emulsion cleaner films are easily penetrated, softened and removed. The activity of the cleaners is accelerated with the use of air, mechanical or ultrasonic agitation. It has particularly good penetrating powers and is therefore suitable for tubular wire work.

OPERATING INFORMATION

For use on Mild Steel & Ferrous Metals

  OPTIMUM RANGE
RONUK METAPREP H.S.C. 60 g/L 40-75 g/L
TEMPERATURE 90°C (119°F) 85-95°C (185-200°F)
SOAK TIME 3 minutes 1-5 minutes
TANKS AND COILS Steels  
AGITATION Air preferred. Mechanical or ultrasonic can also be used.
OPTIMUM Air should be supplied from a filtered low pressure blower.

For use on Copper & Brass (Soak Only)

  OPTIMUM
RONUK METAPREP H.S.C. 50 g/L (40-70 g/L)
TEMPERATURE 65°C (60-70°C)
TIME 1-5 minutes
TANKS AND COILS Steels
AGITATION Air or Mechanical

MAKEUP PROCEDURE

Ronuk Metaprep HSC is dust-free, free flowing and soluble. The tank should be filled 3/4 full with water and warmed to 55-60°C (130-140°F). The required quantity of Ronuk Metaprep H.S.C. should then be slowly added with continuous stirring. After the powder has dissolved, adjust solution to the desired level with water and heat to operating temperature.
Can be used Electrolytically for steel only.

CURRENT DENSITY 2-4 amps / sq. dm.
TEMPERATURE 60-70°C

WASTE DISPOSAL

Ronuk Metaprep HSC solutions are alkaline. Neutralize pH 6 to 8 with an acid and discharge to sewer. The acid must be added slowly and with caution. Avoid eye or skin contact and wear protective clothing and safety goggles. 

CAUTION

Ronuk Metaprep H.S.C. is highly alkaline and can cause severe burns. Avoid contact with skin and eyes. Avoid inhaling powder. Wear protective clothing and safety goggles. Flush exposed areas with clean cold water. In case of injury consult doctor. 

Description / Specification of Pickling Chemicals

We are involved in offering a wide range of Pickling Chemicals to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of  Pickling Chemicals. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design 

RUSGARD 106 DW:

It is a rust preventive oil based on dewatering type. It is used for temporary protection of metal component. 

RUSGARD 16 DW:

It is also based on dewatering type having high viscosity and is used for some longer protection where the metal is to be used continuously. 

RUSGARD 17 ND:

It is drying type rust preventive oil with higher viscosity and good adhesion property on surface.

RUSGARD 18 DR:

It is drying type rust preventor having thick coating on metal surface and used for longer period on exposure to humid condition and air.

PHOSCOPASS:

It is a passivating chemical used after phosphating to seal the pores of the phosphate coating and gives it the corrosion resistance.
 

ZINCOPASS:

It is a chromium based passivating chemical for zinc phosphate process.
 

ZIRCOPASS:

It is a chromium free passivating chemical and meets the need for eco friendly product for chemically pre treating metallic surfaces. Zircopass can be applied by immersion or spraying.

PAINT REMOVERS:
PAINT-STRIP:

It is used for removing epoxy based paints and polyurethane within a short period of time. It is solvent based.
 

STRIP-101:

It is used for removing paints like epoxy base and other types i.e. on plastic components and as well as from metal components.