AUTOMATIC ELECTRIC LTD.

Welcome to AUTOMATIC ELECTRIC LTD.

C.T. Testing Unit

FEATURES
•	Microprocessor controlled
•	Self zero check and calibration check
•	Digital display of %input, ratio error and phase error
•	Manual and auto ranging modes
•	Test 5A and 1A CT with either 1A or 5A reference CT
•	RS 232C port and parallel port for printing
•	Built in real time clock
•	Parameter entry through keyboard

ELECTRICAL SPECIFICATIONS
•	TYPE	SINGLE PHASE
•	OPRATING CURRENT	I A / 5A, 0.5VA
•	AUXILIARY SUPPLY	110V/240V,AC ±20%, 50/60Hz, 60VA.
•	ACCURACY	± 0.5% of reading ±1 % of range
•	FREQUENCY	45Hz to 55Hz or 55Hz to 65Hz.
•	ERROR RANGES	20% (±19.99% ratio error and (±19.99cR* or 680mins.phase error))
		2% (±1.999% and (±1.999cR or 68.0 mins.))
		0.2% (±1999ppm and (±1999µR or 6.80 mins.))
		(cR = Centiradians, µR = Microradians, ppm = Parts Per Million).
•	RESOLUTION	0.05% of range
•	MEASURING TIME	7 seconds irrespective of signal level and error range.
•	OUTPUTS	RS232C port & Parallel port (data in ASCII format).
•	INSULATION RESISTANCE	Greater than 20 Mohms at 500V. DC.
•	DIELECTRIC STRENGTH	2kV RMS for 1 minute
•	OPERATING TEMP.	0°C to 55°C
•	STORAGE TEMP.	-20°C to 70°C
•	HUMIDITY	Upto 95% RH.

MECHANICAL SPECIFICATIONS
•	MODEL	CTU
•	SIZE	180x320x450mm
•	WEIGHT (Appro.)	8.0Kgs

KEYBOARD CONTROLS
0 - 9	Numeric keys to enter values.
•	Decimal point.
ENT	Enter key
RTC	Enter date and time.
SR / VA	Enter serial no. and burden.
PRINT	Take printout of error readings.
SER	Send data to serial port.
% / ACT	Display input in percentage or actual value.
DEG/RAD	Display phase error in minutes or centiradians.
ZERO	Check auto zero.
CAL	Test self calibration.

DISPLAYS AND INDICATIONS
•	4 digit LED display each to display input, ratio error and phase error.
•	LED indications for following quantities
	1) % Input
	2) Minutes and centiradians.
	3) Range for 20%, 2%, 0,2% and Auto
	4) Balance, overrange, zero and calibration.

PRINTING
Date, time, serial no., input (% or actual value), burden, %ratio error, & phase error (minutes or centiradians).

Ordering information

1) Type 2) Model 3) Operating current 4)Operating Frequency 5)Auxiliary supply

H.V. Tester From 2.5 To 200 Kv

INTRODUCTION
Every electrical apparatus or machine Is provided with insulation between live part and earth or between two different sections of live parts. This insulation is required to be tested at high voltage values recommended by applicable relevant standards. The standard Specification for various electrical apparatus specifies Power Frequency Voltage withstand test at different levels depending upon working voltage of electrical apparatus. It is observed from the various standards for electrical equipments that the minimum power frequency voltage withstand test level for electrical insulation is 2kV for one minute. We have, therefore, standardized on manufacture of'AE' High Voltage Breakdown Testers with rated voltage of 5kV.
High Voltage Tests Sets of higher voltage upto 600kV are also manufactured against specific requirement. The standard voltages are 10kV, 15kV, 20kV, 25kV, 30kV, 50kV,100kV, 150kV, 200kV & 300kV. The test sets uplo 30kV are manufactured in Air Cooled design while the sets of 50kV & above are manufactured in Oil Cooled design. The output of these high voltage testers is single phase 50/60Hz. The standard H.T. current rating of air-cooled design as also of oil cooled design upto 150kV is 100mA for 30 minutes. For voltages ranges above 'AE' make 5kV A.C. (with 2.5kV tap) High Voltage Breakdown Tester is portable, sturdy & plug in to start type construction & requires minium table space. It broadly consists of 3 main sections. 1) High Voltage Transformer 2) Variable Voltage Source 3) Control Circuit

1) HIGH VOLATGE TRANSFORMER :
The High voltage transformer is single phase, single pole type & is of double wound resin moulded construction. The H.T. winding is provided with graded insulation such that one end is insulated for 2kVinsulation and is earthed through a current sensing transformer & miiliammeter whereas other end isinsulated for full rated voltage & the same brought out through H.T. Cable & spring loaded Prod.
2) VARIABLE VOLTAGE SOURCE :
Variable Voltage supply is provided through a Dimmerslat (Variable auto-transformer) havingasuitable rating corresponding to the rating of H.V. Transformer. Dimmerstat Is rated for 230Volts A.C. input & 0-270V output. Limit switch at zero position end of Dimmerstat winding is provided to facilitate the H.T. winding to
3) CONTROL CIRCUIT & OTHER FEATURES :
•	ManuaIly operated control transformer (VariabIe auto-transformer) with zero interlock facility.
•	72mm sq. double range (0-2kV / 0-5kV) moving coil rectifier type voltmeter of class 1.5, provided to read NO LOAD H.T. Voltage.
•	72mm sq. double range (0-100mA) moving coil rectifier type A.C. Milliammeter of class 1.5, provided in the earth end of the H.T. winding to read H.T. Current.
•	Automatic tripping circuit is provided for isolation of supply, in the event of failure of the object under test. Rotary switch with four different settings of 5,10, 50 & 100mA is provided on front panel with LED indication
•	M.C.B. for short circuit protection of H.T. transformer & auto transforme
•	H.T. ON push button, Mains ON & H.T ON LED indication.
•	Range selection switch to select 2.5kV or 5kV range with LED indication.
•	Two spring loaded test prods with 1 metre long cable for safe & easy connection of high voltage to test object, (upto 5kV.)

P.T. Testing Unit

DESCRIPTION

It compares & reads the error due to imbalance in signals of test P.T. with reference P.T. and applies necessary proportional signal to nullify the error. Input is displayed in percentage or actual value, and phase error in centiradians or minutes.
On separate key commands the error readings with date, time,% input & burden are sent either to a PC through RS232C port or to a printer connected to parallel port, in order to have report in "view format". The data read from RS232C port can be arranged by using any standard text editor, and a printout can be taken.

FEATURES
•	Micro processor controlled
•	Self zero check and calibration check
•	Digital display of %input, ratio error and phase error.
•	Programmable voltage input
•	Manual and auto ranging modes
•	RS 232C port and parallel port for printing
•	Built in real time clock
•	Parameter entry through keyboard

ELECTRICAL SPECIFICATIONS
•	TYPE	Single phase
•	OPERATING VOLTAGE	3 to 110V AC, 0.5VA
•	AUXILLARY SUPPLY	11OV / 240V. AC ±20%, 50 / 60Hz, 60VA.
•	ACCU RACY	±0.5% of rdg ±1 %of range
•	FREQUENCY	45Hz to 55Hz or 55Hz to 65Hz
•	ERROR RANGES	20% (±19.99% ratio error and (±19.99cR* or 680 mins.phase error))
		2%(±1.999% and (±1.999cR or 68.0 mins.))
		0.2%(±1999ppm and (±1999µR or 6.80 mins.))
		(cR = Centiradians, µR = Microradians, ppm = Parts Per Million).
•	RESOLUTION	0.1 Vac
•	MEASURING TIME	7 seconds, irrespective of signal level and error range.
•	OUTPUTS	RS232C port & Parallel port (data in ASCII format).
•	INSULATION RESISTANCE	Greater than 20 Mohms at 500V. DC.
•	DIELECTRIC STRENGTH	2kV RMS for 1 minute
•	OPERATING TEMP.	0°C to 55°C
•	STORAGE TEMP.	- 20°C to 70°C
•	HUMIDITY	Upto 95% RH

MECHANICAL SPECIFICATIONS
•	MODEL	PTU
•	SIZE	180 x 320 x 450 mm
•	WEIGHT(Appro.)	8.0 kg.

KEYBOARD CONTROLS
0 - 9	Numeric keys to enter values.
.	Decimal point.
ENT	Enter key. And also to enter voltage input.
RTC	Enter date and time.
SR / VA	Enter serial no. and burden.
PRINT	Take printout of error readings.
SER	Send data to serial port.
% / ACT	Display input in percentage or actual value.
DEG / RAD	Display phase error in minutes or centiradians.
ZERO	Check auto zero.
CAL	Test self calibration.

DISPLAYS and INDICATIONS
•	4Digit LED display to indicate input voltage, ratio error and phase error.
•	LED indications for following quantities
	1) % Input
	2) Minutes and centiradians.
	3) Range for 20%, 2%, 0.2% and Auto
	4) Balance, overrange, zero and callibration.

PRINTING

Date, time, serial no., input(% or actual value), burden, % ratio error, & phase error
(minutes or centiradians).

Ordering information

1) Type 2) Model 3) Operating voltage 4) Operating frequency.

Current Transformer

Description / Specification of Current Transformer

We are involved in offering a wide range of Current Transformer to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Current Transformer. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Voltage Transformer

Description / Specification of Voltage Transformer

We are involved in offering a wide range of Voltage Transformer to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Voltage Transformer. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Encapsulated Current Transformers Ae 110 (86) Series

Description / Specification of Encapsulated Current Transformers Ae 110 (86) Series

We are involved in offering a wide range of Encapsulated Current Transformers Ae 110 (86) Series to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Encapsulated Current Transformers Ae 110 (86) Series. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Encapsulated Current Transformers Ae 125 (104) Series

Description / Specification of Encapsulated Current Transformers Ae 125 (104) Series

We are involved in offering a wide range of Encapsulated Current Transformers Ae 125 (104) Series to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Encapsulated Current Transformers Ae 125 (104) Series. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Encapsulated Current Transformers Ae 65 (45) Series

Description / Specification of Encapsulated Current Transformers Ae 65 (45) Series

We are involved in offering a wide range of Encapsulated Current Transformers Ae 65 (45) Series to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Encapsulated Current Transformers Ae 65 (45) Series. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Encapsulated Current Transformers Ae 78 (62) Series

Description / Specification of Encapsulated Current Transformers Ae 78 (62) Series

We are involved in offering a wide range of Encapsulated Current Transformers Ae 78 (62) Series to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Encapsulated Current Transformers Ae 78 (62) Series. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Encapsulatedcurrent Transformers Ae 155 (140) Series

Description / Specification of Encapsulatedcurrent Transformers Ae 155 (140) Series

We are involved in offering a wide range of Encapsulatedcurrent Transformers Ae 155 (140) Series to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Encapsulatedcurrent Transformers Ae 155 (140) Series. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Encapsulated Current Transformers Ae 70 (50) Series

Description / Specification of Encapsulated Current Transformers Ae 70 (50) Series

We are involved in offering a wide range of Encapsulated Current Transformers Ae 70 (50) Series to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Encapsulated Current Transformers Ae 70 (50) Series. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Encapsulated Current Transformers Ae 98 (74) Series

Description / Specification of Encapsulated Current Transformers Ae 98 (74) Series

We are involved in offering a wide range of Encapsulated Current Transformers Ae 98 (74) Series to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Encapsulated Current Transformers Ae 98 (74) Series. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Low Tension Current Transformers

RANGE OF MANUFACTURE :
1. Tapewound ring type current Transformers with and without mounting arrangements. 2. Tapewound ring type CTs with sealing arrangements. 3. Tapewound wound primary CTs (WPL) 4. Resincast (epoxy) BPL CTs. 5. Resincast (epoxy) wound primary (WPL) CTs. 6. Bushing CTs (Fibreglass taped).

CORE BALANCE CTs (Resincast) :
These are used in detecting earth faults of very small magnitude. A three phase cable is passed through these CTs & the unbalanced currents in the three phases set up a differential flux giving rise to a current on the secondary side of these CTs sufficient to actuate a relay.

INTERPOSING CURRENT TRANSFORMERS (Resincast) :
Used in matching the ratios of main feeder CTs for differential protection schemes. These also find application as saturable CTs used in conjunction with main feeder CTs and thus protect the meters connected to these by limiting the current flowing through the meters.

SUMMATION CTs (Resincast) :
Current transformers intended to summate the currents in a number of feeders in association with the feeder Cts is called summation Transformer. The performance / testing of these CTs are governed by IS-6949-1973, BS-3938, IEC-185.

BUSHING CTs (Fibreglass Taped) :
Widely used by Transformer manufacturers for use in oil.

PORTABLE CTs
With class 0.2 accuracy for metering & testing purpose.

FURNACE CTs

CTs WITH ABS CASING AND WITH SEALING ARRANGEMENTS :
Widely used by Electricity Board along with Energy meters.

LOW TENSION POTENTIAL TRANSFORMER (Tapewound / Resincast) :
These are offered in various ratios from 1100/110V to 50/ 75V to suit the exact applications of the clients. Rated burdens upto IOOVA with accuracy classes of I or 0.5 can be offered. Various other types of low tension instruments transformers are also manufactured by us to suit the exact requirements of our clients. Our team of specialised Engineers will be pleased to be of assistance to the clients in proper selection of instrument transformers for their applications.

PROTECTION AND CLASS PS (CLASS X) CTs BOTH IN TAPEWOUND / RESINCAST :
CTs, With class 'PS'/ class'X'for differential protection / BUS coupler application.

Low Tension Indoor Medium Voltage Epoxy Resin Cast Current And Voltage Transformers Details Part 2

DESCRIPTION
AE makes L. T. Transformers in different types & capacities to suit individual requirments. a) Single phase / Three phase, Double wound / Auto wound, Air cooled / Oil cooled. b) Any special (LT) transformer including ultra-isolation transformer. c) Other types of transformers upto 600kA. i) Lighting Tranformer ii) Extra Low Votlage Loading Transformer used for current injection sets iii) Furnace Transformer suitables for use with thyritor controlled furnaces iv) Motor starting Auto Transformer upto 600kA. v) Other as per customer specifications. d) For voltages beyond 660 Volts &7 frequencies other than 50Hz, special construction possible as per customer specifications.

Features
•	Simple - rugged construction, in ssheet steel enclosure / tank.
•	Coils made from high grade CRGO & 99.9% pure copper.
•	High efficiency upto 98.5%.
•	Excellent short time overload capacity.
•	Operating temperature - 45° C.
•	Insulation class - 'B' (higher on request)
•	Conforms to IS 2026.
•	Suitables for indoor use.

Mechanical Construction
•	Terminal accessible through cable entry holes or on opening terminal box.
•	Floor mounting transformers may be provided with MS rollers or base channel.
•	Wall mounting arrangement, wherever feasible can be provided.
•	Off load taps - controlled by link arrangement of tap selector switch.
•	Open transformers without enclosure can be provided for mounting inside a control panel or cubicle

Dimmerstat Continuously Variable Voltage Auto Transformer

DESCRIPTION

Dimmerstat' is registered trade mark for AE make continuously variable voltage auto-transformer. It is the most effective device for stepless, breakless & continuous control of AC voltage & therefore for various parameters, dependent on AC voltage.

The basic Dimmerstat is meant for operation from a nominal input voltage of 240V 1ph AC & can give output voltage anywhere between 0 to 240V or 0 to 270V AC by simple transformer action. Three such Dimmerstats connected electrically in star and mechanically in tandem, become suitable for operation from a nominal input voltage of 415V 3Ph AC and can give output anywhere between 0 to 415V or 0 to 470V.

FEATURES
•	Simple, rugged construction.
•	Coils made from high grade CRGO Silicon Steel & 99.9% pure copper.
•	Output voltage variation is smooth, continuous, breakless & linearly proportional to angular rotation.
•	High efficiency.
•	Negligible waveform & power factor distortion.
•	Excellent short time overload capacity.
•	Remote operation possible by motorization.
•	Wide range of current ratings.
•	High quality carbon brush used for current collection.

ELECTRICAL SPECIFICATIONS

•

MODEL

a) Flush Open Manual (Air Cooled) — F

b) Portable Enclosed Manual (Air Cooled) — P

c) In Tank Manual (Oil Cooled) — T
'F', 'P', T suffixed by 'M' means motor operated models.

•

OPERATING VOLTAGE

For Single Phase - 240V AC, 50-60 Hz. 1- ph.

For Three Phase - 415V AC, 50 -60 Hz., 3 - ph - 4wire.

•

CURRENT RATINGS

For Oil Cooled models, maximum current & continuouscurrent are one & the same.

For Air Cooled models, the ratings are as shown below.

Maximum Current

0.7

2

4

8

10

15

20

28

Continuous Current

0.6

1.8

3.8

6.5

9

11.5

16

22

•

OPERATING TEMP.

0° - 45°C.

•

INSULATION RESISTANCE

Not less than 5 Mohms at 500V DC.

•

DIELECTRIC TEST

2.5kV RMS for 1 minute.

•

STORAGE TEMP.

-9°C to 70°C

•

HUMIDITY

Upto 95% RH

•

CONFORMS TO

I.S. 5142.

Notes :
1	As output voltage is continuously variable, Dimmerstats are rated in terms of current that can be drawn from the output.
2	Oil should be "Transformer Oil" conforming to IS 335, IEC 296.

MECHANICAL CONSTRUCTION
Single phase Dimmerstats are available in 3 types.
•	Portable type (P) with sheet steel enclosure for floor / table use.
•	Flush type (F) with open type construction. Suitable for panel mounting.
•	Tank type (T) immersed in oil in sheet steel tank with rollers.

Three phase Dimmerstat is usually ganged assembly of 3 coils, available in all 3 types: P, F, T.

Higher rating Dimmerstat (above 200 Amps) use 2/3 or more coils in parallel with load balancing arrangements.

Motorised Dimmerstat uses 240V AC Step-Syn Motor having 60 rpm speed at 50Hz. With proper gearing higher torque at lower speed can be achieved. Standard gear ratios used provide sweep time of 8, 15, 30, 45, 60,120secs.

APPLICATIONS
•	Auditorium, Hotels, Conference Halls, Exhibitions, Laboratories etc.,
•	AC Voltage Stabilizers, Rectifiers, Battery Chargers.
•	Temperature control of Ovens, Furnaces.
•	Testing of Instruments, Relays, Circuit Breakers etc.
•	Welding, Electro-plating, Anodizing etc.
•	Colleges & Universities.

Ordering Information (as per code specified below)
1^st block	Output current rating amps	0.7,2,4,8,10,15,20,28,40,50,60,75,100,125,150, 200,300,400, 500,600,800,1000,1200,1500 A.
2^nd block	Dimmerstat (D)	Continuously variable voltage auto transformer.
3^rd block	No. of coils	1, 2, 3, 4, 6, 9, 12, 15.
4^th block	Type of construction.	F, P, T F = Flush, back of panel open. P = Portable, floor, table mounting, air cooled with enclosure. T = In tank, immersed in oil.
5^th block	Provided with motor drive (M)	"Step-syn" 230V 1Ph AC 50Hz. 60 rpm motor having instantaneous start-stop-reverse characteristics.
6^th block	Approx. time in secs. for full rotation sweep time	8,15,30,45,60,120

e.g.	1	2	3	4	5	6	75 A Dimmerstat with 3 coils (Three phase) in oil-cooled tank construction with motor drive having 15 sec. sweep.
e.g.	75	D	3	T	M	15

e.g.	1	2	3	4	8 A Dimmerstat with 1coil (Single phase). Portable type & suitable for manual operation (no motorisation)
e.g.	8	D	1	P

Simiarly, other Dimmerstats can be configured & ordered.

Current Injection Test Unit

Description / Specification of Current Injection Test Unit

We are involved in offering a wide range of Current Injection Test Unit to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Current Injection Test Unit. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Step Syn A.C. Synchronous Motor

DESCRIPTION

These are basically two phase motors. Two-phase supply is normally not available, hence to operate the motors from single phase AC supply, second phase is artificially created by inserting a Capacitor and Resistor combination in series with one of the motor phase windings. Suitable combination of Capacitor and Resistor assembly is supplied along with the motor. The speed of revolution is 60 RPM at 50Hz. Instant stop & reversibility are achieved by means of a single-pole, double throw switch with center OFF position.

FEATURES
•	Instant start & stop.
•	The motors have permanent magnet on the toothed rotor. The rotor is locked with matching teeth on stator, as soon as power is switched OFF.
•	Starting & running current are same.
•	Maximum Torque is 15 to 20% higher than nominal torque.

ELECTRICAL SPECIFICATIONS
TYPE ?	SS-32	SS-72	SS-102	SS-202	SS-302
VOLTAGE	240V.A.C.	240V.A.C.	240V.A.C.	240V.A.C.	240V.A.C.
CURRENT	100mA	100mA	200mA	300mA	500mA
RESISTOR	1kO / 15W	1kO / 15W	1.8kO / 20W	800O / 100W	235O / 200W
CAPACITOR	0.7mfd / 400V.A.C.	0.7mfd / 400V.A.C.	1.0mfd / 400V.A.C.	3.0mfd / 400V.A.C.	4.0mfd / 400V.A.C.
NOM.TORQUE	3kg cm	7kg cm	10kg cm	20kg cm	30kg cm

MECHANICAL SPECIFICATIONS


DIMENSIONS ? TYPE ?	A	B	C	D	E	F	G	ØH	WT. kg
SS-32 / SS-72	87SQ.	8	25	70	17	112	70SQ.	7	1.3
SS-102	108SQ.	9	25	75	12	112	85SQ.	8	2.0
All dimensions are in mm.


DIMENSIONS ? TYPE ?	A	B	C	D	E	F	G	ØH	WT. kg
SS-202	108SQ.	9	34	104	21	159	85SQ.	8	3.4
SS-302	108SQ.	9	34	132	21	187	85SQ.	8	4.5
All dimensions are in mm.

ORDERING INFORMATION

1) Type

Rectifier Units For Electroplating And Anodising

Description / Specification of Rectifier Units For Electroplating And Anodising

We are involved in offering a wide range of Rectifier Units For Electroplating And Anodising to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Rectifier Units For Electroplating And Anodising. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Lighting Transformer Resin Cast Upto 630Kva

Description / Specification of Lighting Transformer Resin Cast Upto 630Kva

We are involved in offering a wide range of Lighting Transformer Resin Cast Upto 630Kva to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Lighting Transformer Resin Cast Upto 630Kva. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Ultra Isolation Transformer

Features
•	Filters power line noise, spikes and transients.
•	Isolates sensitive equipment from noisy power lines.
•	Complete with electrostatic sheilding.
•	Minimizing common mode noise.

ELECTRICAL SPECIFICATIONS
	Single Phase	Three Phase
RATING	1kVA to 25kVA, 50Hz	1kVA to 100kVA, 50Hz
INPUT VOLTAGE	115V / 230V / 240V nominal	380 / 415 / 440V nominal.
ACCEPTABLE INPUT VOLTAGE	±10 %
OUTPUT VOLTAGE	± 10%
MODE of OPERATING	1:1 Isolation Transformer
COMMON MODE NOISE REDUCTION TRANSIENTS, SPIKES, SURGES.	Over 120dB	Over 100dB
COUPLING CAPACITACE	Less than 0.005pF	Less than 0.05pF
D.C. GALVANIC ISOLATION	Over 500M O between any winding or winding to the ground.
BREAKDOWN STRENGTH	2.5kV AC for 1 minute.
ACCEPTABLE LINE FREQUENCY	47 Hz to 63 Hz
LINE LEAKAGE CURRENT	Less than 25µA	Less than 50µA
LOAD REGULATION	Within 3% to 4%	Within 3% to 5%
TERMINATION	On terminal block	On terminal plate
FINISH	7 tank pre-treatment, primer coating & two coas of final finish paint.

Ac Voltage Stabilizers

DESCRIPTION

Servo - Controlled Automatic AC Voltage Stabilizers of 'AE' make are of 'Electro - Mechanical (EMS) type. The purpose of voltage stabilizer is to receive a fluctuating AC voltage of large amplitude & deliver an almost constant voltage, which remains within a very narrow band (± 1%) of the nominal voltage - quality of the AC voltage remains unchanged. The voltage variations, which have become a common phenomenon in current power supply system, cause havoc in modern complicated & sophisticated equipments. The voltage stabilizers are meant to take care of this problem & protect the equipments. They ensure longer life of the equipments & also drastically cut down electricity consumption of equipments leading to continuous reduction in electricity bills. Thus, they play an important role in energy conservation which is need of the day.

The EMS type AC voltage stabilizer basically comprises of the following -
•	Dimmerstat (Continuously variable voltage auto transformer).
•	Buck - Boost Transformer (Optional upto 5kVA 1Ph / 15kVA 3Ph).
•	AC Step-synchronous motor.
•	Solid state electronic control circuit.
•	Two switching triacs.
•	MOVs for surge suppression.

FEATURES
•	Waveform distortion - nil.
•	98 - 99% efficiency (achieved by optimum design & by use of imported hi-quality CRGO laminations & copper of 99.9% purity).
•
•	Speed of correction up to 70V/sec.
•	Response time - less than 20 m/sec.
•	Immune to load PF & supply frequency variations.
•	Power loss 2% max.
•	Duty cycle continuous.
•	Life expectancy - 20 - 25 years.
•	Easy & simple maintenance (with plug-in PCBs).
•	Protections - over voltage / under voltage / overload / single phasing (optional).
•	Very high reliability.
•	Considerable short time overload capacity.
•	Output voltage setting (by potentiometer in Auto Mode & by 'Raise' / 'Lower' Push Button in ManualMode).
•
•	Operation - Auto or Manual.
•	LED Indications for Input Voltage 'High' / 'Low'.
•	Metering (Analogue or Digital) - AC voltmeter with / without selector switch.
•	Non-standard requirements can be catered to, such as AC Ammeter, Frequency Meter, PhaseSequence Meter, Single Phasing Preventer, Stabilizer by-pass arrangement, etc.
•

ELECTRICAL SPECIFICATIONS
•	MODEL	EMS - 12
•	TYPE	Indoor, Floor Mounting.
•	COOLING	Air - Cooled / Oil Cooled / Air - Oil Cooled.
•	INPUT	160 - 260V / 180 - 250V, 1 Phase AC. 300 - 460V / 360 - 460V, 3Phase, 4 Wire (or 3 Wire if required) AC (Balanced or Unbalanced).


•	OUTPUT	230V / 240V ± 1%,1 Phase AC.
		380V / 400V / 415V ± 1%, 3Phase AC.
•	CAPACITY	1 kVA - 2000kVA
•	FREQUENCY	50 - 60Hz.
•	INSULATION RESISTANCE	Not less than 5 Mohms at 500V DC
•	DIELECTRIC TEST	1.5kV RMS for 1 minute.
•	OPERATING TEMP.	0°C to 50°C
•	STORAGE TEMP.	- 9°C to 70°C
•	HUMIDITY	upto 95% RH
•	CONFORMS TO	I.S.9815

NOTES :
•	Input & output voltages, other than specified above, are available on specific request.
•	For 3 Phase balanced supply system, a common controller, connected to any one phase is employed.
•	For 3 Phase unbalanced supply system, 3 individual & independent controllers, one for each of the 3 Phases, are employed.
•	Oil should be 'Transformer Oil' Conforming to IS 335, I.E.C. 296.

MECHANICAL CONSTRUCTION

Panel Meter,Transformer,Voltage Regulator/ stabilizer,Rectifier,Transducer,Break down tester,Test Bench,Relay test kit,Energy saver,Test measuring instruments

APPLICATIONS
CNC Machines, Air Compressors, Textile Machines, Lightings, X-ray & Medical Equipments, Engineering Units, Computers, Pump Sets, Transmitters & many other similar applications.

Ordering information
•	Model
•	Type
•	Cooling
•	Input Voltage (Balanced or Unbalanced)
•	Output Voltage
•	Capacity (kVA)
•	Protections (if required)
•	Non-standard metering.
•	With / without first filling of oil (only for oil cooled units).

Automatic Voltage Stabilizers

DESCRIPTION

The stabilizer consists of a multiple tap auto transformer and solid state control circuit This maintains the output village within ± 12% of nominal voltage for large variations in input voltageI. These can be used for Air conditioners, refrigerators, lights loads etc.

FEATURES
•	Tripping of output village during under voltage and overvoltage conditions.
•	Provision of time delay after startup, under voltage cut of and over voltages cut of conditions.
•	In case time delay is not required, then the stabiliser can be switched on by pressing the instant Start push button provided on the front side.
•	Compact and light weight.
•	Provision of status LED's for input ON, input On equal voltage (low) and input voltage (High) on the front side.

TECHNICAL SPECIFICATIONS
Input Voltage	: 170V to 270V Ac
Output voltage	: 225V ± 12% AC
Output current	: 14Amp
Capacity	: 4KVA
Regulation	: Better than 2%
Under voltage out put	: 140V
Over voltage out put	: 280V
Time Delay	: 120 Seconds (Approximately)
Size	: (250 x 180x170) cubic mm
Weight	: Max.15kg. (depending on the model).

Test Bench Unit

AE Manufactures Test bench units Which can be used for several Application of which few are mentioned below.
•	Testing Induction Motors.
•	Testing of Transformer.
•	Testing of Analog & Digital meters.
•	Testing of electrical devices like MCB, MCCB, ACB etc.

The test enches are coupled with

Our own make Dimmerstats,

Stabilizer or Current Injection

Test kits for carrying out the tests like:

No load test

Full load test

Short circuit test

Temperature rise test

Operating characteristics etc.

ORDERING INFORMATION

Unit under test

Complete technical specifications of the unit under test.

Mechanical dimensions of the test bench desired

Type of meters reqd- Analog / Digital

Any other specific features

Low Tension Power Transformer

RANGE OF MANUFACTURE :
1. Tapewound ring type current Transformers with and without mounting arrangements. 2. Tapewound ring type CTs with sealing arrangements. 3. Tapewound wound primary CTs (WPL) 4. Resincast (epoxy) BPL CTs. 5. Resincast (epoxy) wound primary (WPL) CTs. 6. Bushing CTs (Fibreglass taped).

CORE BALANCE CTs (Resincast) :
These are used in detecting earth faults of very small magnitude. A three phase cable is passed through these CTs & the unbalanced currents in the three phases set up a differential flux giving rise to a current on the secondary side of these CTs sufficient to actuate a relay.

INTERPOSING CURRENT TRANSFORMERS (Resincast) :
Used in matching the ratios of main feeder CTs for differential protection schemes. These also find application as saturable CTs used in conjunction with main feeder CTs and thus protect the meters connected to these by limiting the current flowing through the meters.

SUMMATION CTs (Resincast) :
Current transformers intended to summate the currents in a number of feeders in association with the feeder Cts is called summation Transformer. The performance / testing of these CTs are governed by IS-6949-1973, BS-3938, IEC-185.

BUSHING CTs (Fibreglass Taped) :
Widely used by Transformer manufacturers for use in oil.

PORTABLE CTs
With class 0.2 accuracy for metering & testing purpose.

FURNACE CTs

CTs WITH ABS CASING AND WITH SEALING ARRANGEMENTS :
Widely used by Electricity Board along with Energy meters.

LOW TENSION POTENTIAL TRANSFORMER (Tapewound / Resincast) :
These are offered in various ratios from 1100/110V to 50/ 75V to suit the exact applications of the clients. Rated burdens upto IOOVA with accuracy classes of I or 0.5 can be offered. Various other types of low tension instruments transformers are also manufactured by us to suit the exact requirements of our clients. Our team of specialised Engineers will be pleased to be of assistance to the clients in proper selection of instrument transformers for their applications.

PROTECTION AND CLASS PS (CLASS X) CTs BOTH IN TAPEWOUND / RESINCAST :
CTs, With class 'PS'/ class'X'for differential protection / BUS coupler application.

Digital Panel 16 Range Ammeters

Description / Specification of Digital Panel 16 Range Ammeters

We are involved in offering a wide range of Digital Panel 16 Range Ammeters to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Digital Panel 16 Range Ammeters. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Digital Power Factor Meter

DESCRIPTION

It incorporates solid state circuitry with micro-controller to measure Power Factor of single phase and three phase system.

FEATURES
?/td>	The Meter does not require external transducer, hence panel wiring is reduced.
?/td>	Absence of current is indicated by "Err"
?/td>	Negative sign indicates lagging P.F.

ELECTRICAL SPECIFICATIONS
?/td>	TYPE	Single phase/Three phase single element
?/td>	OPERATIG VOLTAGE	63.5V/110V/240V/440V., 2VA.
?/td>	OPERATING CURRENT	1A/5A, 0.5VA.
?/td>	RESOLUTION	0.001
?/td>	RANGE	0.1 Lag - 1 - 0.1 Lead
?/td>	ACCURACY	?2?/font>
?/td>	AUXILIARY SUPPLY	110V / 240V ?0%, 50 / 60 Hz, 3VA.
?/td>	INSULATION RESISTANCE	Greater than 20 Mohms at 500V DC
?/td>	DIELECTRIC STRENGTH	2kV RMS for 1 minute.
?/td>	OPERATING TEMP.	0°C to 55? C.
?/td>	STORAGE TEMP.	-20°C to 70°C.
?/td>	HUMIDITY	Up to 95% RH.
?/td>	DISPLAY COLOUR	Red

MECHANICAL SPECIFICATIONS
MODEL	PFH 96 D	PFF 96 D	PFH 144 D	PFF 144 D
SIZE (mm)	48 x 96 x 140	96 x 96 x135	72 x 144 x 130	144 x 144 x 130
PANEL CUTUT (mm)	45^+0.6 x 92^+0.8	92 x 92^+0.8	68^+0.7 x 138^+1.0	138 x 138 ^+1.0
WEIGHT (Approx.)	550 gms.	800 gms	900 gms	850 gms

NOTE : Presently model PFH 96 D is available.

Ordering information

1) Type 2) Model 3) Operating voltage 4) Operating current 5) Range 6) Auxiliary supply

True Rms Onsite Programmable Digital Panel Ammeter

DESCRIPTION

It measures true R.M.S. value of sinusoidal and nonsinusoidal voltage or current signals.

ELECTRICAL SPECIFICATIONS
•	TYPE	3 1/2 and 4 1/2 Digits
•	OPERATING VOLTAGE	600V AC 1VA
•	OPERATING CURRENT	1A/5A, 0.5VA
•	ACCURACY	0.5% of FSD ± 5 digits
•	AUXILIARY SUPPLY	110V / 240V ± 10%, 50 / 60 Hz, 3VA
•	WARM-UP TIME	2 minutes
•	RESPONSE TIME	1 second
•	CREST FACTOR	Up to 3
•	INSULATION RESISTANCE	Greater than 20 Mohms at 500V DC.
•	DIELECTRIC STRENGTH	2kV RMS For 1 minute
•	OPERATING TEMP.	0° to 55° C.
•	STORAGE TEMP.	-20° to 70°C.
•	HUMIDITY	Up to 95% RH.
•	DISPLAY COLOUR	Red

MECHANCIAL SPECIFICATIONS
MODEL	VOLTMETER	VRMS H 96 D	VRMS F 96 D	VRMS H 144 D	VRMS F 144 D
MODEL	AMMETER	ARMS H 96 D	ARMS F 96 D	ARMS H 144 D	ARMS F 144 D
SIZE (mm)		48 x 96 x 140	96 x 96 x135	72 x 144 x 130	144 x 144 x 130
PANEL CUTOUT (mm)		45^+0.6 x 92^+0.8	92 x 92^+0.8	66+^0.7 x 138^+1.0	138 x 138^+1.0
WEIGHT (Approx.)		600 gms.	850 gms.	850 gms.	825 gms.

NOTE : Presently models VRMS H 96 D & ARMS H 96 D are available.

Ordering information

1 ) Type 2) Model 3) Operating voltage / current 4) Resolution 5) Auxiliary supply

True Rms Onsite Programmable Digital Panel Voltmeter

DESCRIPTION

It measures true R.M.S. value of sinusoidal and nonsinusoidal voltage or current signals.

ELECTRICAL SPECIFICATIONS
•	TYPE	3 1/2 and 4 1/2 Digits
•	OPERATING VOLTAGE	600V AC 1VA
•	OPERATING CURRENT	1A/5A, 0.5VA
•	ACCURACY	0.5% of FSD ± 5 digits
•	AUXILIARY SUPPLY	110V / 240V ± 10%, 50 / 60 Hz, 3VA
•	WARM-UP TIME	2 minutes
•	RESPONSE TIME	1 second
•	CREST FACTOR	Up to 3
•	INSULATION RESISTANCE	Greater than 20 Mohms at 500V DC.
•	DIELECTRIC STRENGTH	2kV RMS For 1 minute
•	OPERATING TEMP.	0° to 55° C.
•	STORAGE TEMP.	-20° to 70°C.
•	HUMIDITY	Up to 95% RH.
•	DISPLAY COLOUR	Red

MECHANCIAL SPECIFICATIONS
MODEL	VOLTMETER	VRMS H 96 D	VRMS F 96 D	VRMS H 144 D	VRMS F 144 D
MODEL	AMMETER	ARMS H 96 D	ARMS F 96 D	ARMS H 144 D	ARMS F 144 D
SIZE (mm)		48 x 96 x 140	96 x 96 x135	72 x 144 x 130	144 x 144 x 130
PANEL CUTOUT (mm)		45^+0.6 x 92^+0.8	92 x 92^+0.8	66+^0.7 x 138^+1.0	138 x 138^+1.0
WEIGHT (Approx.)		600 gms.	850 gms.	850 gms.	825 gms.

NOTE : Presently models VRMS H 96 D & ARMS H 96 D are available.

Ordering information

1 ) Type 2) Model 3) Operating voltage / current 4) Resolution 5) Auxiliary supply

Dc Energy Meter

Description / Specification of Dc Energy Meter

We are involved in offering a wide range of Dc Energy Meter to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Dc Energy Meter. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Digital Energy Meter (Counter Type)

Description / Specification of Digital Energy Meter (Counter Type)

We are involved in offering a wide range of Digital Energy Meter (Counter Type) to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Digital Energy Meter (Counter Type). Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Digital Energy Meter (Led Display And Rs 485 Interface)

Description / Specification of Digital Energy Meter (Led Display And Rs 485 Interface)

We are involved in offering a wide range of Digital Energy Meter (Led Display And Rs 485 Interface) to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Digital Energy Meter (Led Display And Rs 485 Interface). Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Electronic Led Frequency Meter

DESCRIPTION
It is used to measure the applied frequency, functionally similar to vibrating reed meter. The meter incorporates light emitting diodes LEDs which are used instead of vibrating reeds to indicate applied frequency. The frequency is determined by blinking LEDs. When applied frequency matches with the frequency marked on the dial, that particular LED blinks with maximum intensity. When the applied frequency is mid way between two adjacent LEDs, both LEDs blink. When the meter is switched on all the LEDs glow sequentially for a period of 1 to 1.5 seconds, thereafter it will indicate the applied frequency.
All voltage ranges are available in single meter. Terminal screws with washers are provided only for specific voltage as per requirement & remaining two terminals are covered with insulated caps. In case of 96mm & 144mm instruments, two sets of LEDs with the same scale range can be offered, giving two independent meters in one casing (Dual Scale). This facilitates in comparing the frequency of two voltage supplies for paralleling operation.

FEATURES
•	No vibrating parts.
•	No aging effect.
•	Faster response.
•	Lighter in weight.
•	Low power consumption
•	No effect of external vibration
•	Visible in dark & from distance.

ELECTRICAL SPECIFICATIONS
•	TYPE	ELECTRONIC
•	OPERATING VOLTAGE	110V~125V, 220V-250V, 380V~440V.
•	POWER CONSUMPTION	Less than 3VA (Single scale), Less than 6VA (Double scale).
•	MEASURING METHOD	Time measurement between consecutive cycles.
•	DISPLAY	Box LED, Colour Red/Green, Size 6.3 X 3.7mm
•	SAMPLING RATE	2-3 samples/sec.
•	RESPONSE TIME	Less than 1 sec.
•	INSULATION RESISTANCE	Greater than 20 Mohms at 500V DC.
•	DIELECTRIC STRENGTH	2kV RMS for 1 minute.
•	OPERATING TEMP.	-10°C to 55°C
•	STORAGE TEMP.	-20°C to 70°C
•	HUMIDITY	Upto 95% RH
•	CONFORMS TO	I.S. 1248 / B.S. 89. / I.E.C. 51. (Part - 4)

AVAILABLE RANGES
MODEL				ELFS 72	ELFS 96	ELFS 96	ELFS 144	ELFS144
RANGE	Resolution	LEDS	Acc. #	Single Scale	Single Scale	Double Scale	Single Scale	Double Scale
45 -50 -55	*	13	±1
47 - 50 -53	0.5Hz	13	±1
55 - 60 - 65	*	13	±1
57 - 60 - 63	0.5Hz	13	±1
370-400-430	5Hz	13	±1
45 - 50 - 55	0.5Hz	21	±1	--		--
48 - 50 - 52	0.2Hz	21	±0.5	--		--
55- 60 - 65	0.5Hz	21	±1	--		--
58 - 60 - 62	0.2Hz	21	±0.5	--		--
380-400-420	2Hz	21	±0.5	--		--

# % of center frequency Panel Meter,Transformer,Voltage Regulator/ stabilizer,Rectifier,Transducer,Break down tester,Test Bench,Relay test kit,Energy saver,Test measuring instruments

Available models

* There are 11LEDs in a row in steps of 1Hz for range (45-50-55Hz)/(55 - 60 - 65Hz) with additional 2 LEDs for (49.5 and 50.5Hz) / (59.5 and 60.5Hz) respectively.

NOTE : Frequency Meter For Other Range / Resolution Shall Be Supplied on Request If Feasible

MECHANICAL SPECIFICATIONS
MODEL	ELFS 72	ELFS 96	ELFD 96	ELFS 144	ELFD 144
SIZE (mm)	72 x 72 x 70	96 x 96 x 70	96 x 96 x 70	144 x 144 x 60	144 x 144 x 60
PANEL CUTOUT (mm)	60 x 60^+0.7	92 x 92 ^+0.8	92 x 92 ^+0.8	138 x 138^+1.0	138 x 138^+1.0
WEIGHT (Approx.)	350gms.	400gms.	600gms.	500gms.	700gms.

TERMINAL ARRANGEMENT

ELFS 72	ELFS 96 / ELFD 96


ELFS 144	ELFD 144

Ordering information

1) Type 2) Model 3) Range 4) Operating Voltage

Vibrating Reed Frequency Meter

DESCRIPTION
It is used to measure the applied frequency. Vibrating Reed Frequency meters indicate the supply frequency by means of individual reeds, when rated voltage ± 20% is applied across the terminals of the meter, the particular reed, whose natural frequency of vibration coincides with the supply frequency, vibrates with full amplitude. In case the supply frequency falls midway between two reeds both the reeds vibrate, at reduced amplitude. The amplitude of vibration at the tip of reeds is high enough for a distinct indication. The instrument can be operated at 110V, 220V, or 440V. Terminal screws with washers are provided for the selected operating voltage & remaining two terminals are covered with insulated caps. In case of RFD96 and RFD144 instruments, two sets of reeds with the same scale range can be offered, giving two independent meters in one casing. This facilitates in comparing the frequency of two voltage supplies for paralleling operation

FEATURES
•	Vibrating reed.
•	No aging effect.
•	Faster response.
•	Lighter in weight.
•	Low power consumption
•	Rugged construction
•	High reliability

ELECTRICAL SPECIFICATIONS
•	TYPE	Vibrating Reed
•	OPERATING VOLTAGE	110V~125V, 220V~250V, 380V~440V.
•	POWER CONSUMPTION	Less than 0.3VA,0.6VA and 1.2VA for respective operating voltage in 72 & 96. 26 Sizes
		Less than 0.6VA, 1.2VA, 2.4VA for respective operating voltage in 144 size.
•	DIELECTRIC STRENGTH	2kV RMS for 1 minute.
•	OPERATING TEMP.	-10°C to 55°C
•	STORAGE TEMP.	-20°C to 70°C
•	HUMIDITY	Upto 95% RH
•	CONFORMS TO	I.S.1248 / I.E.C. 60051(Part4).

AVAILABLE RANGES
MODEL				RFS 72	RFS 96	RFS96	RFS 144	RFS 144
RANGE	Resolution	Reeds	Acc.#	Single Scale	Single Scale	Dual Scale	Single Scale	Dual Scale
45 - 50 - 55	*	13	±1
47 - 50 - 53	0.5Hz	13	±1
55 - 60 - 65	*	13	±1
57 - 60 - 63	0.5Hz	13	±1
45 - 50 - 55	0.5Hz	21	±1	--	--	--
55 - 60 -65	0.5Hz	21	±1	--	--	--

# % of centre frequency Available models
*	There are 11 reeds in a row in setps of 1Hz for range 45 - 50 - 55Hz (55 - 60 - 65Hz) with additional 2reeds for 49.5 and 50.5Hz (59.5 and 60.5Hz) respectively.

MECHANICAL SPECIFICATIONS
MODEL	RFS 72	RFS 96	RFD 96	RFS144	RFD 144
SIZE (mm)	72 x 72 x 70	96 x 96 x 70	96 x 96 x 70	144 x 144 x 60	144 x 144 x 60
PANEL CUTOUT (mm)	68 x 68^+0.7	92 x 92^+0.8	92 x 92^+0.8	138 x 138^+1.0	138 x 138^+1.0
WEIGHT (Approx.)	300gms.	360gms.	550gms.	650gms.	950gms.


RFS 72	RFS 96 / RFD 96


RFS144	RFD 144

Ordering information :1) Type 2) Operating Voltages 3) Model 4) Range

Dual Kwh Meter

Description / Specification of Dual Kwh Meter

We are involved in offering a wide range of Dual Kwh Meter to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Dual Kwh Meter. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Maximum Demand Controller Mdc 1000

Description / Specification of Maximum Demand Controller Mdc 1000

We are involved in offering a wide range of Maximum Demand Controller Mdc 1000 to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Maximum Demand Controller Mdc 1000. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Phase Sequence Indicator

DESCRIPTION

It is a rotating disc type instrument. The disc rotates in clockwise direction when correctly connected to incoming three phase power supply. Black arrow on white disk indicates correct phase sequence. If rotation is anti-clockwise then it indicates that one of the phases is reversed. It is suitable for use only in horizontal position and should not be left in circuit. Three, 1 meter long red, yellow, blue colour leads with clips and sheaths are provided.

ELECTRICAL SPECIFICATIONS
•	TYPE	Electro-mechanical
•	OPERATING VOLTAGE	50V to 500V AC
•	FREQUENCY	25 Hz to 60 Hz.
•	INSULATON RESISTANCE	Greater than 20 Mohms at 500V DC
•	DIELECTRIC STRENGTH	2kV RMS for one minute
•	OPERATING TEMP.	-10°C to 55°C
•	STORAGE TEMP.	-20° to 70°C
•	HUMIDITY	upto 95% RH

MECHANICAL SPECIFICATIONS
•	MODEL	PSI 96 M
•	SIZE	96 X 96 X 56mm (Supplied With carry bag)
•	WEIGHT (Appro.)	600gms

Ordering information 1) Type 2) Model

Portable Instrument Multi Range And Multi Parameter (Medium Size Multi Range With Bakelite Housing)

DESCRIPTION

Protable Moving Coil DC, Moving Coil Rectifier type AC, Moving Iron AC ammeters & voltmeters and can be used in conjunction with transducers for measurement of frequency, power factor and low power factor wattage. Single phase dynamometric instrument is used for measurement of power at Unity Power Factor (UPF).

FEATURES / ADVANTAGES
•	Instruments with accuracy class 1.0, 1.5.
•	Instruments with multiple scale (refer table).
•	Robust housing suitable for schools, workshops, field operations, for continuous use.

ELECTRICAL SPECIFICATIONS
MODEL	TYPE	SCALE	RANGE	ACCURACY
PORT- MSMB-1	MOVING IRON AC VOLT - AMMETER	Quadruple	0 - 62.5/125/250/500V & 0 - 2.5/5/10/25A or 0-75/150/300/600V & 0-1/3/10/30A	1%
PORT-MSMB-2	MOVING COIL DC VOLT-AMMETER	Quadruple	0 - 0.075/15/150/600V & 0 - 1.5/15/75/150A (with 75mV shunt)	1.5%
PORT MSMB-3	MOVING COIL DC & AC VOLTMETE	Quadruple	0 - 1.5/15/150/600V DC 0 - 6/60/300/600V AC	1.5%
	FREQUENCY METER	Single	45-55Hz or 55-65Hz or 380-420Hz at Single Voltage 62.5/10V/220/440V	1%
	POWER FACTOR METER 1 - Phase	Single	0.5 Lag - Unity - 0.5 Lead or 0.3 Lag-Unity-0.3Lead at Single Voltage 110V/220V/440V & Single Current 1A/5A	2°
	POWER FACTOR METER 3-Phase - 1Element	Single	0.5 Lag-Unity-0.5 Lead or 0.3 Lag-Unity-0.3 Lead at Single Voltage 110V/220V/440V & Single Current 1A/5A	2°
	LPF WATTMETER 1 Phase	Dual	62.5V/ 125V to 300V/600V & 50mA/100mA to 5A/10A	0.5%

MODEL	TYPE		*POTENTIAL COIL (A)	CURRENT COIL (A)	ACCURACY
PORT-MSMB-4	WATT METER 1Ph UPF	SPSC	75, 150, 300, 600	0.5, 1, 2, 2.5, 5, 10, 20	1.0%
		DPSC	75/150, 150/300, 300/600
		TPSC	75/150/300, 150/300/600
		SPDC	75, 150, 300, 600	0.5/1, 1/2, 2.5/5, 5/10, 10/20
		DPDC	75/150, 150/300, 300/600
		TPDC	75/150/300, 150/300/600

* 62.5/ 125/ 250/ 500V INSTEAD OF 75 / 150 / 300/ 600 V - ON REQUEST.

Mechanical Specification

SIZE			HOUSING MATERIAL	MODEL IDENTIFICATION	SCALE		WEIGHT kg. (Appro.)
LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING MATERIAL	MODEL IDENTIFICATION	LENGHT mm (Appro.)	DIVISIONS	WEIGHT kg. (Appro.)
240	185	120	Bakelite	MSMB-	150	80 ~ 120	3

Ordering information

Ammeter / Voltmeter

1) Type 2) Model 3) Range 4) Scale 5) Accuracy

Frequency Meter

1) Type 2) Model 3) Range 4) Voltage 5) Accuracy

Watt / PF Meter

1) Type 2) Model, Parameter, Phase & Range 3) Operating Voltage & PTR
4) Operating Current & CTR.

Synchroscope

DESCRIPTION
'AE' SYNCHROSCOPE is categorized into two types A) Electro-mechanical and B) Electronic.

ELECTRO-MECHANICAL TYPE

It incorporates a POINTER and LED to indicate synchronising condition. If the generator- (II) frequency is higher or lower than that of mains- (I) the pointer rotates in clockwise or anti-clockwise direction respectively. The speed and direction of rotation depends upon difference in frequencies, which guides the operator to speed-up or slow-down the generator. Synchronising condition is determined by dark lamp method, wherein the pointer coincides with synchronising mark and the LED does not glow. The LED glows in accordance with difference in phase, frequency and amplitude of voltages. When the pointer is towards the bright LED, it indicates the antiphase condition.

FEATURES
•	Rugged construction.
•	Easy serviceability.
•	Wide operating voltage range.

ELECTRICAL SPECIFICATIONS
•	TYPE	Electro-mechanical
•	VOLTAGE AT SYNCHRONISM	110V ± 2%
•	OPERATING VOLTAGE	110V ± 20% (for other voltages use separate PT box.)
•	FREQUENCY	50 / 60Hz ± 5%
•	SYNCHRONISING CONDITION	Dark lamp method
•	ACCURACY	2°
•	ANGLE OF ROTATION	360°
•	POWER CONSUMPTION	3 VA for MAINS - (I) & 6VA for GENERATOR - (II)
•	INSULATION RESISTANCE	Greater than 20 Mohms at 500V. DC.
•	DIELECTRIC TEST	2kV RMS for One minute
•	OPERATING TEMP.	-10°C to 55°C
•	STORAGE TEMP.	-20°C to 70°C
•	HUMIDITY	Upto 95% RH
•	INDICATION	Moving pointer & LED
•	CONFORMS TO	I.S. 1248 / I.E.C. 51 (Part-5)

MECHANICAL SPECIFICATIONS
•	MODEL	SYN96M	SYN144M
•	SIZE	96 x 96 x 85mm	144 x 144 x 60 mm
•	PAN EL CUTOUT	92 x 92^+0.8mm	138 x 138^+1.0mm
•	WEIGHT (Appro.)	Approx.750gms.	1 kg.

CAUTION : The meter is not to be left in circuit after synchronising.

ELETRONIC TYPE

It incorporates circle of LEDs which glows sequentially in either clockwise or anti-clockwise direction at variable speed in accordance with difference in frequencies of mains & generator. Synchronising condition is indicated by the glowing LED of "SYNCHRO ON" position. Antiphase condition is indicated by glowing LED of "SYNCHRO OFF" position at the bottom. This LED glows under following conditions

1) Absence of mains-(l) and presence of generator voltage-(ll)

2) If generator - (Il) voltage crosses ± 20% When frequencies of both supplies are equal, phase angle between two voltages is indicated by glowing of LED at an approximate angle with respect to "SYNCHRO ON" position.

FEATURES
•	Continuous operation.
•	No moving parts.
•	Low power consumption.
•	Visible in dark.

ELECTRICAL SPECIFICATIONS
•	TYPE	Electronic
•	VOLTAGE AT SYNCHRONISM	110V ± 2%
•	OPERATING VOLTAGE	110V ± 20% (for other voltages use separate PT box.)
•	FREQUENCY	50/60Hz ± 5%
•	SYNCHRONISING CONDITION	Glowing of "SYNCHRO ON" LED
•	ACCURACY	2°
•	ANGLE OF ROTATION	360°
•	POWER CONSUMPTION	2VA for MAINS - (I) & 0.25VA for GENERATOR - (II)
•	INSULATION RESISTANCE	Greater than 20 Mohms at 500V. DC.
•	DIELECTRIC TEST	2kV RMS for One minute
•	OPERATING TEMP.	-10°C to 55°C
•	STORAGE TEMP.	-20°C to 70°C
•	HUMIDITY	Upto 95% RH
•	INDICATION	Rotating LED
•	CONFORMS TO	I.S. 1248 / I.E.C. 51 (Part-5)

MECHANICAL SPECIFICATIONS
•	MODEL	SYN 96 E	SYN 144 E
•	SIZE	96 x 96 x 75mm	144 x 144 x 60 mm
•	PAN EL CUTOUT	92 x 92^+0.8mm	138 x 138^+1.0mm
•	WEIGHT(Appro.)	450gms.	650 gms.

Ordering information 1) Type 2) Model 3) Operating voltage 4) Frequency

Moving Coil 240 Long Scale Instruments

DESCRIPTION

Moving coil instruments with circular scale of 240° employ a platinum taut band for suspension of moving coil assembly instead of pivot & jewel system. It is less prone to sluggishness & zero shift due to frictionless movement.
These meters are basically used for the measurement of DC current & voltage, and can be used with built in rectifier for the measurement of AC current & voltage in the frequency range 45~65Hz. / 400Hz. The meters measure average value. It can be scaled to indicate RMS values (on request).
These instruments are not recommended for non-sinusoidal waveforms of current & voltage. The other indications like Frequency, Power & Power factor can be offered with suitable external transducers. Speed indication is possible if used with AC tacho-generator (not in the scope of AE).

FEATURES
•	Long scale instruments.

ELECTRICAL SPECIFICATIONS
•	TYPE	MOVING COIL 240°.
•	OPERATING VOLTAGE	60mV to 600V.
•	OPERATING CURRENT	500µA to 30A & Above 30A with external shunt.
•	ACCURACY CLASS	2.5 for SQ48, 1.5 for SQ72 & SQ96, 1.0 for SQ14 4, SQ110.
•	DIELECTRIC TEST	2kV RMS for 1 min.
•	OPERATING TEMP.	-10°C to 55°C
•	STORAGE TEMP.	-20°C to 70°C
•	HUMIDITY	Up to 95% RH
•	CONFORMS TO	I.S. 1248 / I.E.C. 60051 (Part 2)

MODEL	SQ 48	SQ 72	SQ 96	SQ 144	SQ 110
ACCURACY CLASS	2.5	1.5^A	1.0^A	1.0^A	1.0^A
D.C.AMMETER (MIN.)	0-500µA
(MAX.)	0-100mA^B	0 - 30A^C
D.C.VOLTMETER (MIN.)	0 - 60mV
(MAX.)	0-150mV^B	0 - 600V
A.C.AMMETER (MIN.)	0-10mA^B	0 - 10mA
(MAX.)	0-30A^B	0 - 30A
A.C.VOLTMETER (MIN.)	0-10V^B	0 - 10V
(MAX.)	0-600V^B	0 - 600V
FREQ. METER	POSSIBLE^B	40Hz TO 100Hz AT 110V ~ 440V
WATT / VAR METER	POSSIBLE^B	POSSIBLE^D	1PH, 3PH-2 / 3E :110V~440V,1A/5A		POSSIBLE^E
VA METER	POSSIBLE^B	POSSIBLE^D	3PH-2 / 3E : 110V~440V, 1A/5A		POSSIBLE^E
PF METER	POSSIBLE^B	POSSIBLE^D	1PH, 3PH-1E : 110V~ 440V, 1A / 5A

Note : Range below minimum & above maximum on request if feasible.
A	Accuracy Class 0.5 for all Frequency meters, 1.5 for SQ96,SQ144,SQ110, AC Ammeter, AC / Ammeter / Voltmeter & Power meter, 2° for all Power Factor meter,

B	SQ48 - i) DC / AC Voltmeter, AC Ammeter with external box. ii) Frequency meter, Power meter with external transducer box.

C	For higher ranges use AE external shunts. (Refer Data Sheet for Shunts).
D	SQ72 - Power & Power factor meter with external transducer box.
E	SQ 110-Power meter with external transducer box.

MECHANICAL SPECIFICATIONS
MODEL		SQ 48	SQ 72	SQ 96	SQ 144	SQ 110
FLANGE (mm)		48 x 48	72 x 72	96 x 96	144 x 144	110 x 110
PANEL CUTOUT(mm)		45 x 45^+0.6	68 x 68^+0.7	92 x 92^+0.8	138 x 138^+1.0	100 Ø, 5 Ø, 4 holes 90x90
DEPTH (mm)	DC	55	55	55	60	100
DEPTH (mm)	AC	55	75	75^A	60^A	100
SCALE LENGTH (mm)(Appro.)		70 - 75	105 -110	150 - 155	225 - 230	175 - 180
WEIGHT (gms.) (Appro.)	DC	200	250	300	500	450
WEIGHT (gms.) (Appro.)	AC	200	350	400^B	600^B	650

A	Depth 100mm for SQ96 & SQ144 Power meter.
B	Weight 1.2kg for SQ96 Power meter, 1.5kg for SQ144 Power meter.

Ordering information
For all Models	1) Type 2) Model 3) Range
Additional information for power and power factor measurments.	4) frequency 5) Operating Voltage 6) Operating Current 7) PTR 8) CTR.

Moving Coil Ammeters And Voltmeters (Slide In Scale)

DESCRIPTION
Moving Coil Instruments are protected from damage or breakage under adverse conditions due to spring loaded jewel & pivot system. These Instruments are free from external magnetic field influences because of centre magnet system and are "CE" certified. Voltmeters are made upto 600V for direct connection and upto 1200V with / without external multiplier with sensitivity 1000 ohms / V. Higher sensitivities are available. Scale printed for other variables viz. Speed, Temp, pH, kW, kVAR, Hz or Cos ¢ (p, etc. can be supplied on request.
Ammeters with internal shunts are available upto 30 Amps and for higher currents upto 12000 Amps use external shunts of 50mV, 60mV, 75mV etc. (Please refer data sheet no. Shunt 03/99.)

FEATURES
•	SCALE	Linear.
•	SCALE COLOUR	Special colour scales & marks for different ranges, (on request).
•	GLASS	Anti-glare, (on request).
•	HOUSING	Engineering plastic.
•	TERMINAL PROTECTION	Shrouded terminals to protect from accident, (on request).

ELECTRICAL SPECIFICATIONS
•	TYPE	Moving Coil Slide in scale.
•	OPERATING VOLTAGE	50mV to 600V.
•	OPERATING CURRENT	l00nA to 30A. & Above 30A external shunt.
•	ACCURACY	Class 1.5.
•	DIELECTRIC TEST	2kV RMS for 1 min.
•	OVERLOAD CONTINUOUS	1.2 times.
•	OVERLOAD SHORT TIME	2 times V_N / 10 times _IN for 5 seconds.
•	OPERATING TEMP.	-10°C to 55°C.
•	STORAGE TEMP.	-20°C to 70°C.
•	HUMIDITY	up to 95% RH
•	CONFORMS TO	I.S. 1248 / I.E.C. 60051 (Part 2).

Mechanical Specifications
MODEL	SMC 72	SMC 96
SIZE (mm)	72 x 72 x 60	96 x 96 x 60
PANEL CUTOUT (mm)	68 x 68 ^+0.7	92 x 92 ^+0.8
SCALE LENGTH (mm) (Appro.)	60	90
WEIGHT ( gms.) (Appro.)	130	190

Note : METERS ARE ALSO AVAILABLE IN 48x48x45 (SMC 48) & 144 x 144 x 60 (SMC 144) IN NON SLIDE IN DIAL VERSION.

MODEL	SMC 48	SMC 144
SIZE (mm)	48 x 48 x 45	144 x 144 x 50
PANEL CUTOUT (mm)	45 x 45 ^{+ 0.7}	138 x 138 ^+0.8
SCALE LENGTH (mm) (Appro.)	40	145
WEIGHT ( gms.) (Approx.)	100	400

Ordering information

1) Type 2) Model 3) Operating Voltage / Current 4) mV in case of Ammeter with external shunt.

Moving Iron Ammeters And Voltmeters (Slide I Scale)

DESCRIPTION
Moving Iron Instruments are protected from damage or breakage under adverse condition due to its spring loaded jewel & pivot system. These Instruments are free from external magnetic field influences because of magnetic shielding & are 'CE' certified. These instruments have a very efficient oil damping system, which gives almost a deadbeat movement to the pointer, without irksome oscillation. The movement is light yet sturdy and has a large torque to weight ratio which assures long life to instruments.
These indicate true RMS values practically independent of waveform even of high harmonics. The scale is compressed initially. Readability starts from 10 to 15 degree approximately.

FEATURES
•	Scale	Non-linear.
•	Suppression	Initial suppression for Voltmeter & End suppression upto 6 times for Ammeter. (on request)
•	Scale Colour	Special colour scales and marks for different ranges, (on request).
•	Housing	Engineering plastic.
•	Terminal Protection	Shrouded terminals to protect from accident, (on request).
•	Glass	Anti - glare. (on request)

ELECTRICAL SPECIFICATIONS
•	TYPE	Moving Iron Slide In Scale.
•	OPERATING VOLTAGE (For Voltmeter) Burden	15V to 600V. 100V / 110V for PT secondary. 15V to 30V - <100mA, 50V to 100V - < 30mA, 110V to 200V - <15mA, 200V to 600V - <7.5mA.
•	OPERATING CURRENT (For Ammeter) Burden	1 A to100A in 72x72, 1A to 200A in 96x96 1A / 5A for CT secondary. 0.25A to 30A - < 1VA, Above 30A - < 1.5 VA.
•	FREQUENCY	45 ~ 65Hz. (400Hz. on request).
•	ACCURACY	Class 1.5
•	DIELECTRIC TEST	2kV RMS or 1 minute.
•	OVERLOAD CONTINUOUS	1.2 times
•	OVERLOAD SHORT TIME	2 times V_N / 10 times I_N for 5 seconds.
•	OPERATING TEMP.	-10°C to 55°C
•	STORAGE TEMP.	-20°C to 70°C
•	HUMIDITY	upto 95% RH
•	CONFORMS TO	I.S. 1248 / I.E.C. 60051 (Part 2).

MECHANICAL SPECIFICATIONS
MODEL	SMI 72 (Slide in)	SMI 96 (Slide in)
SIZE ( mm )	72 x 72 x 60	96 x 96 x 60
PANEL CUTOUT ( mm )	68 x 68 ^+0.7	92 x 92 ^+0.8
SCALE LENGTH ( Appro. mm )	60	90
WEIGHT ( Appro. gms. )	<145 For 72 SQ Amps <180 For 72 SQ Volts	<200 For 96 SQ Amps <230 For 96 SQ Volts

Note : METERS ARE ALSO AVAILABLE IN 48x48x45 (SMI 48) & 144x144x60 (SMI 144) IN NON SLIDE IN DIAL VERSION.

MODEL	SMI 48	SMI 144
SIZE (mm)	48 x 48 x 45	144 x 144 x 50
PANEL CUTOUT (mm)	45 x 45 ^+0.6	138 x 138 ^+1.0
SCALE LENGTH (Appro. mm.)	40	145
WEIGHT (Appro. gms.)	100	400

Ordering information

1) Type 2) Model 3) Operating Voltage & PTR Voltmeter 4) Operating Current & CTR For Ammeter.

Maximum Demand Meter

DESCRIPTION

Maximum Demand meter is used for monitoring thermal loading in Power Distribution systems, Networks, Machines etc. It indicates maximum loading current over a period. Short-period current peaks are not registered but long overloads are registered.
In the Maximum Demand meter the measuring current flows through the bimetal spiral which is temperature sensitive. The free end of the spiral is connected to a black measuring pointer. The moving system is activated by heat generated by the current flowing through the spiral. The instrument is provided with an additional red slave pointer with a higher friction, which makes it to remain at its maximum position, which determines the maximum average loading current. The high torque of metallic movement drags the red pointer along with the black pointer. The red pointer remains stationary at the maximum value reached. This can be reset by rotating the knob provided on front facia. To prevent false indication due to fluctuations in ambient temperature, an additional bimetallic spiral is wound in opposite direction, which is mounted on the same spindle to compensate variation in temperature from -10 to + 55 degrees Centigrade.
Frequently there is a need to measure instantaneous current simultaneously & hence moving iron movement having the same range is incorporated in the same meter.

FEATURES
•	RMS measurement of maximum current.	•	20% overload capacity.
•	Long current peaks are registered.	•	Instantaneous current measurement.
•	Red pointer to indicate maximum current reached.	•	Sturdy movement.
•	Analogue Indication.

ELECTRICAL SPECIFICATIONS

•

TYPE

BIMETALLIC; ANALOGUE AMMETER.

•

OPERATING CURRENT

1 Amp or 5Amp

•

FREQUENCY

40 ~ 65Hz.

•

ACCURACY

± 3% for resettable red pointer (Bimetallic).

± 1.5% instantaneous value pointer (Moving Iron)

•

THERMAL LAG (SETTING TIME)

15 minutes (standard) & 8 minutes (on special request).

•

VA BURDEN

Approx. 3.5VA for Bimetallic Ammeters &

Approx. 4VA for Bimetallic And Moving Iron Ammeter.

•

INSULATION RESISTANCE

Greater than 20 Mohms at 500V DC

•

DIELECTRIC TEST

2kV rms for 1 minute.

•

OPERATING TEMP.

-10°C to 55°C (for Analogue Instrument)

•

STORAGE TEMP.

-20°C to 70°C

•

HUMIDITY

upto 95% RH

MECHANICAL SPECIFICATION
MODEL	MDIS 72 A	MDID 72A	MDIS 96A*	MDID 96A*
SIZE (mm)	72 x72 x 70	72 x72 x 70	96 x 96 x70	96 x 96 x70
PANEL CUTOUT (mm)	68 x 68^+0.7	68 x 68^+0.7	92 x 92^+0.8	92 x 92^+0.8
SCALE LENGTH (Approx.) OF BIMETALLIC SYSTEM	60mm	60mm	90mm	90mm
SCALE LENGTH (Approx.) OF MI SYSTEM	N.A.	38mm	N.A.	70mm
WEIGTH (Approx.) (gms)	180	200	230	250
* These models are available at present

PRIMARY CURRENT	SECONDARY CURRENT 5AMPS OR 1AMPS
PRIMARY CURRENT	-SCALE-
MODEL	MDIS 72A	MDID 72A		MDIS 96A		MDID 96A
100%	120%	120%	200%	120%	120%	200%
10A	12A	12A	0......... 10/20A	12A	12A	0.................. 10/20A
15A	18A	18A	0......... 15/30A	18A	18A	0.................. 15/30A
20A	24A	24A	0..........20/40A	24A	24A	0...................20/40A
25A	30A	30A	0..........25/50A	30A	30A	0...................25/50A
30A	36A	36A	0..........30/60A	36A	36A	0...................30/60A
40A	48A	48A	0..........40/80A	48A	48A	0...................40/80A
50A	60A	60A	0.........50/100A	60A	60A	0.................50/100A
60A	72A	72A	0.........60/120A	72A	72A	0.................60/120A
75A	90A	90A	0........75/150A	90A	90A	0.................75/150A
80A	96A	96A	0.........80/160A	96A	96A	0.................80/160A
100A	120A	120A	0.......100/200A	120A	120A	0...............100/200A
125A	150A	150A	0.......125/250A	150A	150A	0...............125/250A
150A	180A	180A	0.......150/300A	180A	180A	0...............150/300A
200A	240A	240A	0.......200/400A	240A	240A	0...............200/400A
250A	300A	300A	0.......250/500A	300A	300A	0...............250/500A
300A	360A	360A	0......300/600A	360A	360A	0...............300/600A
400A	480A	480A	0......400/800A	480A	480A	0.................400/800
500A	600A	600A	0.....500/1000A	600A	600A	0.............500/1000A
600A	720A	720A	0.....600/1200A	720A	720A	0.............600/1200A
750A	900A	900A	0.....750/1500A	900A	900A	0.............750/1500A
800A	960A	960A	0.....800/1600A	960A	960A	0.............800/1600A
1000A	1.2kA	1.2kA	0............1/2kA	1.2kA	1.2kA	0....................1/2kA
1200A	1.4kA	1.4kA	0......1.2/2.4kA	1.4kA	1.4kA	0...............1.2/2.4kA
1500A	1.8kA	1.8kA	0.........1.5/3kA	1.8kA	1.8kA	0..................1.5/3kA
2000A	2.4kA	2.4kA	0............2/4kA	2.4kA	2.4kA	0....................2/4kA
2500A	3.0kA	3.0kA	0.........2.5/5kA	3.0kA	3.0kA	0.................2.5/5kA
3000A	3.6kA	3.6kA	0............3/6kA	3.6kA	3.6kA	0....................3/6kA
4000A	4.8kA	4.8kA	0............4/8kA	4.8kA	4.8kA	0....................4/8kA
5000A	6.0kA	6.0kA	0..........5/10kA	6.0kA	6.0kA	0..................5/10kA

Ordering information
1) Type 2) Model 3) Operating Current 4) C.T.R. 5) Thermal lag / Setting Time

Multi Function Meter Ae90xx With Dg Monitor And Printer

Description / Specification of Multi Function Meter Ae90xx With Dg Monitor And Printer

We are involved in offering a wide range of Multi Function Meter Ae90xx With Dg Monitor And Printer to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Multi Function Meter Ae90xx With Dg Monitor And Printer. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Multifunction Meter Ae9000 Ae9001 Ae9002 Ae9003 Part I

Description / Specification of Multifunction Meter Ae9000 Ae9001 Ae9002 Ae9003 Part I

We are involved in offering a wide range of Multifunction Meter Ae9000 Ae9001 Ae9002 Ae9003 Part I to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Multifunction Meter Ae9000 Ae9001 Ae9002 Ae9003 Part I. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Multifunction Meter Ae9000 Ae9001 Ae9002 Ae9003 Part Ii

Description / Specification of Multifunction Meter Ae9000 Ae9001 Ae9002 Ae9003 Part Ii

We are involved in offering a wide range of Multifunction Meter Ae9000 Ae9001 Ae9002 Ae9003 Part Ii to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Multifunction Meter Ae9000 Ae9001 Ae9002 Ae9003 Part Ii. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Multifunction Meter Ae9000 With Thd Measurement

Description / Specification of Multifunction Meter Ae9000 With Thd Measurement

We are involved in offering a wide range of Multifunction Meter Ae9000 With Thd Measurement to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Multifunction Meter Ae9000 With Thd Measurement. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Portable Instrument 1Ph And 3Ph Power Factor Meter (Large Size Dynamometric In Wodden Housing)

DESCRIPTION

Protable dynamometric types instruments, incorporating single element / two elements or three elements power measurement methods and specially designed to be operated in horizontal position.

FEATURES / ADVANTAGES
•	Instruments with accuracy class 0.5 for 1 Ph Watt, 1.5 for 3Ph, 2° for PF.
•	Instruments with multiple scale available (refer table).
•	Robust housing suitable for schools, workshops and field operations for continuous use.

ELECTRICAL SPECIFICATIONS
TYPE	MODEL		POTENTIAL COIL (A)	CURRENT COIL (A)	ACCURACY
Watt Meter With Low Power Factor	PORT LSDW-1	TPDC	75/150/300,150/300/600	0.5/1,1/2,2.5/5,5/10,10/20	1.5%
WATT METER	PORT LSDW-2	SPSC	75,150,300,600	0.5,1,2,2.5,5,10,20	0.5%
		DPSC	75/150,150/300,300/600
		TPSC	75/150/300,150/300/600
		SPDC	75,150,300,600	0.5/1,1/2,2.5/5,5/10,10/20
		DPDC	75/150,150/300,300/600
		TPDC	75/150/300,150/300/600
	PORT LSDW-3	SPSC	75,150,300,600	0.5,1,2,2.5,5,10,20	1.5%
	PORT LSDW-4	SPSC	75,150,300,600	0.5,1,2,2.5,5,10,20
	PORT LSDW-4	DPDC	75/150,150/300,300/600	0.5/1,1/2,2.5/5,5/10,10/20
	PORT LSDW-5	SPSC	75,150,300,600	0.5, 1, 2, 2.5, 5, 10, 20
	PORT LSDW-5	SPDC	75,150,300,600	0.5/1,1/2,2.5/5,5/10,10/20
VAR METER	PORT LSDW-6	SPSC	75,150,300,600	0.5,1,2,2.5,5,10,20	1.5%
	PORT LSDW-6	DPDC	75/150,150/300,300/600	0.5/1,1/2,2.5/5,5/10,10/20
	PORT LSDW-7	SPSC	75,150,300,600	0.5, 1, 2, 2.5, 5, 10, 20
	PORT LSDW-7	SPDC	75,150,300,600	0.5/1,1/2,2.5/5,5/10,10/20
POWER FACTOR METER	PORT LSDW-8	SPSC	75,150,300,600	0.5,1,2,2.5,5,10,20	2°
		DPSC	75/150,150/300,300/600
		TPSC	75/150/300,150/300/600
		SPDC	75,150,300,600	0.5/1,1/2,2.5/5,5/10,10/20
		DPDC	75/150,150/300,300/600
		TPDC	75/150/300,150/300/600
	PORT LSDW-9	SPSC	75,150,300,600	0.5,1,2,2.5,5,10,20

SELECTION OF RANGES

Upper limit of measuring range for meters shall be one of the following values -

1, 1.2, 1.5, 2, 2.5, 3, 4, 5, 6, 7.5, 8 or their decimal multiples.

Example for selection of proper range

1 ) Formula for 1 Phase active power

P(max) = VI COS¢ Where COS¢ = 1.

If Voltage = 500V & Current = 2.5A calculated power = 500 x 2.5 x 1 = 1.25kW.

If the calculated value is 1.25kW 0 - 1.2kW or 0 - 1.25kW shall be selected as a range for power.

2) Formula for 3 Phase active power with PT & CT.

P(max) = √ 3VI COS¢ x PTR x CTR Where COS ¢ = 1.

If Voltage = 110V & Current = 5A PTR = 400kV/110V CTR = 1000A/5A

calculated power = √ 3 x 110x5 x (400x1000/110) x (1000/5)= 692MW.

If the calculated value is 692MW 0 - 600MW or 0 - 750MW shall be selected as a range for power.

Note :
•	All Wattmeters are calibrated at cos¢ = 1 and Varmeter at sin¢ = 1
•	All Low Power Factor Wattmeters are calibrated at cos¢ = 0.2 lag.
•	Voltage & Current range other than specified can be supplied on request, if feasible.

Mechanical Specifications

Fig. 1	Fig. 2

SIZE	LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING MATERIAL	MODEL IDENTIFICATION	SCALE		WEIGHT kg. (Approx.)
SIZE	LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING MATERIAL	MODEL IDENTIFICATION	LENGHT mm (Approx.)	DIVISIONS	WEIGHT kg. (Approx.)
1	300	200	155/190	Wooden Box	LSDW-	150	100 ~ 150	4 ~ 5
2	225	355	190/225	Wooden Box	LSDW-	150	100 ~ 150	5.5 ~ 7.5

Ordering information

1) Type 2) Model 3) Parameter, Phase, Range 3) Operating Voltage & PTR
4) Operating Current & CTR.

Portable Instrument D.C. And A.C. Ammeters (Large Size Precision In Wodden Housing)

DESCRIPTION

Protable Moving Coil or Moving Coil rectifier type instruments or Dynamometric type of instruments, specially designed to be operated in horizontal position (also in inclined position upto 45°) & can be carried along safely.

FEATURES / ADVANTAGES
•	Instruments with 0.5 accuracy class.
•	Instruments with multiple scale available (refer table).
•	Robust housing suitable for schools, workshops and field operations for continuous use.
•	Precision instruments suitable for standard laboratories.

ELECTRICAL SPECIFICATIONS
MODEL	TYPE	SCALE	RANGE	ACC.
PORT LSPW-1	D.C. µ - AMMETER	Single	500µA,1000µA	0.5%
	D.C. µ - AMMETER	Dual	500µA / 1000µA
	D.C. MILLI-AMMETER	Single	1mA, 2.5mA, 3mA, 5mA, 7.5mA, 10mA, 25mA, 30mA, 50mA, 75mA, 100mA, 250mA, 300mA, 500mA, 750mA, 1000mA
	D.C. MILLI-AMMETER	Dual	1/2mA, 2.5/5mA, 5/10mA, 10/20mA, 15/30mA, 25/50mA, 50/100mA, 150/300mA, 250/500mA. 500/1000mA.
	D.C. AMMETER	Single	1A,2.5A,3A,5A,10A,15A,20A,25A,30A
	D.C. AMMETER	Dual	1/2A, 2.5/5A, 5/10A, 10/20A, 15/30A.
	D.C.MILLIVOLTMETER	Single	25mV, 50mV, 75mV, 100mV, 150mV, 300mV, 500mV, 1000mV.
		Dual	25/50mV, 50/100mV,75/150mV,100/200mV 150/300mV, 250/500mV, 500/1000mV.
		Triple	25/50/100mV, 50/100/200mV,75/150/300mV 150/300/600mV, 250/500/1000mV.
		Quadruple	25/50/100/200mV, 125/250/500/1000mV
	D.C. VOLTMETR	Single	1V,2.5V,3V,5V,7.5V,10V,15V,20V,25V,30V, 50V,75V, 100V. 150V,200V,250V,300V,500V,600V,1000V.
		Dual	1/2V, 2.5/5V, 5/10V, 30/60V, 50/100V, 75/150V, 100/200V, 150/300V,250/500V, 300/600V, 500/1000V.
		Triple	1.5/3/7.5V, 3/7.5/15V, 7.5/15/30V, 15/30/75V, 25/50/100V,75/150/300V, 125/250/500V, 150/300/600V
		Quadruple	1.5/3/7.5/15V, 3/7.5/15/30V, 7.5/15/30/60V, 15/30/75/150V, 30/75/150/300V, 75/150/300/600V.
PORT LSPW-2	A.C. AMMETER	Single	0.5A, 1A, 2.5A, 5A, 10A,15A,20A,30A	0.5%
PORT LSPW-2	A.C. AMMETER	Dual	1/2A,2.5/5A,5/10A & also 0.2/1A, 0.5/2.5A, 1/5A,2/10A,10/20A,15/30A.
	A.C. VOLTMETER	Single	62.5V, 75V, 125V, 150V, 250V, 300V, 500V, 600V.
		Dual	62.5/125V, 75/150V, 125/250V, 150/300V, 250/500V. 300/600V.
		Triple	62.5/125/250V, 75/150/300V,125/250/500V. 150/300/600V

MECHANICAL CONSTRUCTION

SIZE	LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING MATERIAL	MODEL IDENTIFICATION	SCALE		WEIGHT kg. (Approx.)
SIZE	LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING MATERIAL	MODEL IDENTIFICATION	LENGTH mm (Approx.)	DIVISION nos.	WEIGHT kg. (Approx.)
1	300	200	155	Wooden Box	LSPW-1	150	100 ~ 150	4
2	300	200	190	Wooden Box	LSPW-2	150	100 ~ 150	5

Ordering information

1) Type 2) Model 3) Scale 4) Range 5) Accuracy

Portable Instrument D.C. And A.C. Ammeters (Medium Size Standard With Bake Lite Housing)

DESCRIPTION

Portable Moving Coil DC, Moving Coil rectifier type AC, Moving Iron AC ammeters & voltmeters suitable for use in schools, laboratories, workshops & for field operation. Specially designed to be operated in horizontal position (also in inclined position upto 45°) & can be carried along safely.

FEATURES / ADVANTAGES
•	Instruments with accuracy class 1.0 for DC/AC, 1.5 for Rectifier type AC.
•	Instruments with multiple scale (refer table).
•	Robust housing suitable for schools, workshops and field operations for continuous use.

ELECTRICAL SPECIFICATION
MODEL	TYPE	SCALE	RANGE	ACC.
PORT MSSB-1	D.C.µ -Ammeter	Single	50µA,100µA, 150µA,250µA,500µA,1000µA.	1.0%
	D.C.µ -Ammeter	Dual	50/100µA, 100/200µA, 150/300µA, 250/ 500µA, 500/1000µA.
	D.C. MILLI-Ammeter	Single	1mA, 2.5mA, 3mA, 5mA, 7.5mA,10mA, 25mA, 30mA, 50mA, 75mA,100mA, 250mA, 300mA, 500mA, 750mA, 1000mA.
	D.C. MILLI-Ammeter	Dual	1/2mA, 2.5/5mA, 5/10mA,10/20mA,15/30mA, 25/50mA, 50/100mA,150/300mA, 250/500mA, 500/1000mA.
	D.C.AMMETER	Single	1A, 2.5A, 3A, 5A, 10A, 15A, 20A, 25A, 30A (INT.SHUNT).
	D.C.AMMETER	Dual	1/2A, 2.5/5A, 5/10A, 10/20A,15/30A (INT.SHUNT).
	D.C. MILLIVOLTMETER	Single	10mV, 25mV, 50mV, 75mV,100mV, 150mV, 300mV, 500mV,1000mV.
		Dual	10/20mV, 25/50mV, 50/100mV, 75/150mV 100/200mV, 150/300mV, 250/500mV, 500/1000mV.
		Triple	25/50/100mV, 50/100/200mV, 75/150/300mV, 150/300/600mV, 250/500/1000mV.
		Quadruple	25/50/100/200mV, 125/250/500/1000mV.
	D.C. VOLTMETER	Single	1V, 2.5V, 3V, 5V, 7.5V, 10V, 15V, 20V, 25V, 30V, 50V, 75V, 100V, 150V, 200V, 250V, 300V, 500V, 600V, 1000V.
		Dual	1/2V, 2.5/5V, 5/10V, 30/60V, 50/100V, 75/150V, 100/200V, 150/300V, 250/500V, 300/600V, 500/1000V.
		Triple	1.5/3/7.5V, 3/7.5/15V, 7.5/15/30V, 15/30/75V, 25/50/100V, 75/150/300V, 125/250/500V, 150/300/600V, 250/500/1000V.
		Quadruple	1.5/3/7.5/15V, 3/7.5/15/30V, 7.5/15/30/60V, 15/30/75/150V, 30/75/150/300V, 75/150/300/600V, 125/250/500/1000V.
PORT MSSB-2	A.C. MILLI-AMMETER	Single	10mA, 50mA, 100mA, 250mA, 500mA, 1000mA.	1.5%
	A.C .AMMETER	Single	1A, 5A, 10A, 15A, 20A, 25A, 30A.
	A.C. VOLTMETER	Single	3V, 7.5V, 10V, 15V, 20V, 25V, 50V, 100V, 150V, 300V, 600V.
		Dual	7.5/15V, 10/20V, 15/30V, 25/50V, 50/100V, 150/300V, 300/600V.
		Triple	3/7.5/15V, 7.5/15/30V, 15/30/75V, 30/75/150V, 75/150/300V, 125/250/500V, 150/300/600V.
PORT MSSB-3	A.C.AMMETER	Single	0.2A, 0.5A, 1A, 2.5A, 5A, 10A, 15A, 20A, 30A, 50A, 100A.	1.0%
		Dual	0.5/1A, 1/2A, 2.5/5A 5/10A & also 0.2/1A, 0.5/2.5A, 1/5A, 2/10A, 10/20A, 15/30A, 25/30A, 50/100A.
		Triple	1/3/10A, 3/10/30A, 10/30/100A, 5/10/25A, 10/25/50A, 25/50/100A.
		Quadruple	1/3/10/30A, 3/10/30/100A, 5/10/25/50A, 10/25/50/100A.
		Quadruple	1/3/10/30/100A, 5/10/25/50/100A
	A.C.VOLTMETER	Single	15V, 30V, 62.5V, 75V, 125V, 150V, 250V, 300V, 500V, 600V.
		Dual	15/30V, 30/60V, 62.5/125V, 75/150V, 125/250V, 150/300V, 250/500V, 300/600V.
		Triple	15/3075V, 62.5/125/250V, 75/150/300V, 125/250/500V, 150/300/600V.

MECHANICAL CONSTRUCTION

Size			HOUSING MATERIAL	MODEL IDENTIFICATION	SCALE		WEIGHT kg. (Approx.)
LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING MATERIAL	MODEL IDENTIFICATION	LENGTH mm(Approx.)	DIVISIONs	WEIGHT kg. (Approx.)
240	185	80	Bakelite	MSSB-	150	80 ~ 120	2.5

Ordering information

1) Type 2) Model 3) Scale 4) Range 5) Accuracy

Portable Instrument D.C. And A.C. Ammeters (Small Size Standard With Polycarbonate Housing)

DESCRIPTION

Portable Moving Coil DC, Moving Coil rectifier type AC, Moving Iron AC ammeters & voltmeters suitable for cartier replica use in schools, laboratories, workshops & for field operation. Specially designed to be operated in horizontal position (also in inclined position upto 45? & can be carried along safely.

FEATURES
?	Instruments with accuracy class 1.0 for DC, 1.5 for AC.
?	Instruments with multiple scale (refer table).
?	Robust housing suitable for schools, workshops field operations, for continuous use.
?	Instruments with high resistance to shock & vibrations.

ELECTRICAL SPECIFICATIONS
MODEL	TYPE	SCALE	RANGE	ACC.
PORT SSSP-1	D.C. µ-AMMETER	Single	250µA, 500µA, 1000µA	1.0%
	D.C. µ-AMMETER	Dual	250µA, 500µA, 1000µA
	D.C. MILLI-AMMETER	Single	1mA, 2.5mA, 3mA, 5mA, 7.5mA, 10mA, 25mA, 30mA, 50mA, 75mA, 100mA, 250mA, 300mA 500mA, 750mA, 1000mA
	D.C. MILLI-AMMETER	Dual	1/2mA, 2.5/5mA, 5/10mA, 10/20mA, 15/30mA, 25/50mA, 50/100mA, 150/300mA, 250/500mA. 500/1000mA.
	D.C. AMMETER	Single	1A, 2.5A, 3A, 5A, 10A, 15A, 20A, 25A, 30A (INT.SHUNT)
	D.C. AMMETER	Dual	1/2A, 2.5/5A, 5/10A, 10/20A, 15/30A. (INT. SHUNT)
	D.C.MILLI- VOLTMETER	Single	50mV, 75mv, 100mV, 150mV, 300mV, 500mV, 1000mV.
		Dual	50/100/200mV, 75/150mV, 100/200mV, 150/300/600mV, 250/500/1000mV.
		Triple	50/100/200mV, 75/150/300mV, 150/300/600mV, 250/500/1000mV.
	DC VOLTMETR	Single	1V,2.5V,3V,5V,7.5V,10V,15V,20V,25V,30V,50V, 75V, 100V, 150V, 200V, 250V, 300V, 500V, 600V.
		Dual	1/2V, 2.5/5V, 5/10V, 15/30V, 30/60V, 50/100V, 75/150V, 100/200V, 150/300V,250/500V, 300/600V.
		Triple	1.5/3/7.5V, 15/30/75V, 25/50/100V,75/150/300V. 125/250/500V. 150/300/600V.
PORT SSSP-2	A. C. MILLI-AMMETER	Single	10mA, 50mA.	1.5%
PORT SSSP-2	A.C.VOLTMETER	Single	10V, 15V, 20V, 25V, 50V, 100V, 150V, 300V, 600V.	1.5%
PORT SSSP-3	A.C.AMMETER	Single	0.5A, 1A, 2.5A, 5A, 10A.	1.5%
	A.C.AMMETER	Dual	0.5/1 A. 1/2A. 2.5/5A. 5/10A.
	A.C.VOLTMETER	Single	62.5V, 75V, 125V, 150V, 250V, 300V, 500V, 600V.
		Dual	62.5/125V, 75/150V, 125/250V,150/300V. 250/500V. 300/600V.
		Triple	62.5/125/250V, 75/150/300V, 125/250/500V, 150/300/600V.

MECHANICAL CONSTRUCTION

Size			HOUSING mm	MODEL mm	SCALE		WEIGHT gm. (Approx.)
LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING mm	MODEL mm	LENGTH mm (Approx.)	DIVISIONS	WEIGHT gm. (Approx.)
115	110	50	Polycarbonate	SSSP-	90	30 ~ 50	400

Ordering information

1) Type 2) Model 3) Scale 4)Range 5) Accuracy

Portable Instrument D.C. And A.C. Voltmeters (Large Size Precision In Wodden Housing)

DESCRIPTION

Protable Moving Coil or Moving Coil rectifier type instruments or Dynamometric type of instruments, specially designed to be operated in horizontal position (also in inclined position upto 45°) & can be carried along safely.

FEATURES / ADVANTAGES
•	Instruments with 0.5 accuracy class.
•	Instruments with multiple scale available (refer table).
•	Robust housing suitable for schools, workshops and field operations for continuous use.
•	Precision instruments suitable for standard laboratories.

ELECTRICAL SPECIFICATIONS
MODEL	TYPE	SCALE	RANGE	ACC.
PORT LSPW-1	D.C. µ - AMMETER	Single	500µA,1000µA	0.5%
	D.C. µ - AMMETER	Dual	500µA / 1000µA
	D.C. MILLI-AMMETER	Single	1mA, 2.5mA, 3mA, 5mA, 7.5mA, 10mA, 25mA, 30mA, 50mA, 75mA, 100mA, 250mA, 300mA, 500mA, 750mA, 1000mA
	D.C. MILLI-AMMETER	Dual	1/2mA, 2.5/5mA, 5/10mA, 10/20mA, 15/30mA, 25/50mA, 50/100mA, 150/300mA, 250/500mA. 500/1000mA.
	D.C. AMMETER	Single	1A,2.5A,3A,5A,10A,15A,20A,25A,30A
	D.C. AMMETER	Dual	1/2A, 2.5/5A, 5/10A, 10/20A, 15/30A.
	D.C.MILLIVOLTMETER	Single	25mV, 50mV, 75mV, 100mV, 150mV, 300mV, 500mV, 1000mV.
		Dual	25/50mV, 50/100mV,75/150mV,100/200mV 150/300mV, 250/500mV, 500/1000mV.
		Triple	25/50/100mV, 50/100/200mV,75/150/300mV 150/300/600mV, 250/500/1000mV.
		Quadruple	25/50/100/200mV, 125/250/500/1000mV
	D.C. VOLTMETR	Single	1V,2.5V,3V,5V,7.5V,10V,15V,20V,25V,30V, 50V,75V, 100V. 150V,200V,250V,300V,500V,600V,1000V.
		Dual	1/2V, 2.5/5V, 5/10V, 30/60V, 50/100V, 75/150V, 100/200V, 150/300V,250/500V, 300/600V, 500/1000V.
		Triple	1.5/3/7.5V, 3/7.5/15V, 7.5/15/30V, 15/30/75V, 25/50/100V,75/150/300V, 125/250/500V, 150/300/600V
		Quadruple	1.5/3/7.5/15V, 3/7.5/15/30V, 7.5/15/30/60V, 15/30/75/150V, 30/75/150/300V, 75/150/300/600V.
PORT LSPW-2	A.C. AMMETER	Single	0.5A, 1A, 2.5A, 5A, 10A,15A,20A,30A	0.5%
PORT LSPW-2	A.C. AMMETER	Dual	1/2A,2.5/5A,5/10A & also 0.2/1A, 0.5/2.5A, 1/5A,2/10A,10/20A,15/30A.
	A.C. VOLTMETER	Single	62.5V, 75V, 125V, 150V, 250V, 300V, 500V, 600V.
		Dual	62.5/125V, 75/150V, 125/250V, 150/300V, 250/500V. 300/600V.
		Triple	62.5/125/250V, 75/150/300V,125/250/500V. 150/300/600V

MECHANICAL CONSTRUCTION

SIZE	LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING MATERIAL	MODEL IDENTIFICATION	SCALE		WEIGHT kg. (Approx.)
SIZE	LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING MATERIAL	MODEL IDENTIFICATION	LENGTH mm (Approx.)	DIVISION nos.	WEIGHT kg. (Approx.)
1	300	200	155	Wooden Box	LSPW-1	150	100 ~ 150	4
2	300	200	190	Wooden Box	LSPW-2	150	100 ~ 150	5

Ordering information

1) Type 2) Model 3) Scale 4) Range 5) Accuracy

Portable Instrument D.C. And A.C. Voltmeters (Medium Size Standard With Bake Lite Housing)

DESCRIPTION

Portable Moving Coil DC, Moving Coil rectifier type AC, Moving Iron AC ammeters & voltmeters suitable for use in schools, laboratories, workshops & for field operation. Specially designed to be operated in horizontal position (also in inclined position upto 45°) & can be carried along safely.

FEATURES / ADVANTAGES
•	Instruments with accuracy class 1.0 for DC/AC, 1.5 for Rectifier type AC.
•	Instruments with multiple scale (refer table).
•	Robust housing suitable for schools, workshops and field operations for continuous use.

ELECTRICAL SPECIFICATION
MODEL	TYPE	SCALE	RANGE	ACC.
PORT MSSB-1	D.C.µ -Ammeter	Single	50µA,100µA, 150µA,250µA,500µA,1000µA.	1.0%
	D.C.µ -Ammeter	Dual	50/100µA, 100/200µA, 150/300µA, 250/ 500µA, 500/1000µA.
	D.C. MILLI-Ammeter	Single	1mA, 2.5mA, 3mA, 5mA, 7.5mA,10mA, 25mA, 30mA, 50mA, 75mA,100mA, 250mA, 300mA, 500mA, 750mA, 1000mA.
	D.C. MILLI-Ammeter	Dual	1/2mA, 2.5/5mA, 5/10mA,10/20mA,15/30mA, 25/50mA, 50/100mA,150/300mA, 250/500mA, 500/1000mA.
	D.C.AMMETER	Single	1A, 2.5A, 3A, 5A, 10A, 15A, 20A, 25A, 30A (INT.SHUNT).
	D.C.AMMETER	Dual	1/2A, 2.5/5A, 5/10A, 10/20A,15/30A (INT.SHUNT).
	D.C. MILLIVOLTMETER	Single	10mV, 25mV, 50mV, 75mV,100mV, 150mV, 300mV, 500mV,1000mV.
		Dual	10/20mV, 25/50mV, 50/100mV, 75/150mV 100/200mV, 150/300mV, 250/500mV, 500/1000mV.
		Triple	25/50/100mV, 50/100/200mV, 75/150/300mV, 150/300/600mV, 250/500/1000mV.
		Quadruple	25/50/100/200mV, 125/250/500/1000mV.
	D.C. VOLTMETER	Single	1V, 2.5V, 3V, 5V, 7.5V, 10V, 15V, 20V, 25V, 30V, 50V, 75V, 100V, 150V, 200V, 250V, 300V, 500V, 600V, 1000V.
		Dual	1/2V, 2.5/5V, 5/10V, 30/60V, 50/100V, 75/150V, 100/200V, 150/300V, 250/500V, 300/600V, 500/1000V.
		Triple	1.5/3/7.5V, 3/7.5/15V, 7.5/15/30V, 15/30/75V, 25/50/100V, 75/150/300V, 125/250/500V, 150/300/600V, 250/500/1000V.
		Quadruple	1.5/3/7.5/15V, 3/7.5/15/30V, 7.5/15/30/60V, 15/30/75/150V, 30/75/150/300V, 75/150/300/600V, 125/250/500/1000V.
PORT MSSB-2	A.C. MILLI-AMMETER	Single	10mA, 50mA, 100mA, 250mA, 500mA, 1000mA.	1.5%
	A.C .AMMETER	Single	1A, 5A, 10A, 15A, 20A, 25A, 30A.
	A.C. VOLTMETER	Single	3V, 7.5V, 10V, 15V, 20V, 25V, 50V, 100V, 150V, 300V, 600V.
		Dual	7.5/15V, 10/20V, 15/30V, 25/50V, 50/100V, 150/300V, 300/600V.
		Triple	3/7.5/15V, 7.5/15/30V, 15/30/75V, 30/75/150V, 75/150/300V, 125/250/500V, 150/300/600V.
PORT MSSB-3	A.C.AMMETER	Single	0.2A, 0.5A, 1A, 2.5A, 5A, 10A, 15A, 20A, 30A, 50A, 100A.	1.0%
		Dual	0.5/1A, 1/2A, 2.5/5A 5/10A & also 0.2/1A, 0.5/2.5A, 1/5A, 2/10A, 10/20A, 15/30A, 25/30A, 50/100A.
		Triple	1/3/10A, 3/10/30A, 10/30/100A, 5/10/25A, 10/25/50A, 25/50/100A.
		Quadruple	1/3/10/30A, 3/10/30/100A, 5/10/25/50A, 10/25/50/100A.
		Quadruple	1/3/10/30/100A, 5/10/25/50/100A
	A.C.VOLTMETER	Single	15V, 30V, 62.5V, 75V, 125V, 150V, 250V, 300V, 500V, 600V.
		Dual	15/30V, 30/60V, 62.5/125V, 75/150V, 125/250V, 150/300V, 250/500V, 300/600V.
		Triple	15/3075V, 62.5/125/250V, 75/150/300V, 125/250/500V, 150/300/600V.

MECHANICAL CONSTRUCTION

Size			HOUSING MATERIAL	MODEL IDENTIFICATION	SCALE		WEIGHT kg. (Approx.)
LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING MATERIAL	MODEL IDENTIFICATION	LENGTH mm(Approx.)	DIVISIONs	WEIGHT kg. (Approx.)
240	185	80	Bakelite	MSSB-	150	80 ~ 120	2.5

Ordering information

1) Type 2) Model 3) Scale 4) Range 5) Accuracy

Portable Instrument D.C. And A.C. Voltmeters (Small Size Standard With Polycarbonate Housing)

DESCRIPTION

Portable Moving Coil DC, Moving Coil rectifier type AC, Moving Iron AC ammeters & voltmeters suitable for use in schools, laboratories, workshops & for field operation. Specially designed to be operated in horizontal position (also in inclined position upto 45°) & can be carried along safely.

FEATURES
•	Instruments with accuracy class 1.0 for DC, 1.5 for AC.
•	Instruments with multiple scale (refer table).
•	Robust housing suitable for schools, workshops field operations, for continuous use.
•	Instruments with high resistance to shock & vibrations.

ELECTRICAL SPECIFICATIONS
MODEL	TYPE	SCALE	RANGE	ACC.
PORT SSSP-1	D.C. µ-AMMETER	Single	250µA, 500µA, 1000µA	1.0%
	D.C. µ-AMMETER	Dual	250µA, 500µA, 1000µA
	D.C. MILLI-AMMETER	Single	1mA, 2.5mA, 3mA, 5mA, 7.5mA, 10mA, 25mA, 30mA, 50mA, 75mA, 100mA, 250mA, 300mA 500mA, 750mA, 1000mA
	D.C. MILLI-AMMETER	Dual	1/2mA, 2.5/5mA, 5/10mA, 10/20mA, 15/30mA, 25/50mA, 50/100mA, 150/300mA, 250/500mA. 500/1000mA.
	D.C. AMMETER	Single	1A, 2.5A, 3A, 5A, 10A, 15A, 20A, 25A, 30A (INT.SHUNT)
	D.C. AMMETER	Dual	1/2A, 2.5/5A, 5/10A, 10/20A, 15/30A. (INT. SHUNT)
	D.C.MILLI- VOLTMETER	Single	50mV, 75mv, 100mV, 150mV, 300mV, 500mV, 1000mV.
		Dual	50/100/200mV, 75/150mV, 100/200mV, 150/300/600mV, 250/500/1000mV.
		Triple	50/100/200mV, 75/150/300mV, 150/300/600mV, 250/500/1000mV.
	DC VOLTMETR	Single	1V,2.5V,3V,5V,7.5V,10V,15V,20V,25V,30V,50V, 75V, 100V, 150V, 200V, 250V, 300V, 500V, 600V.
		Dual	1/2V, 2.5/5V, 5/10V, 15/30V, 30/60V, 50/100V, 75/150V, 100/200V, 150/300V,250/500V, 300/600V.
		Triple	1.5/3/7.5V, 15/30/75V, 25/50/100V,75/150/300V. 125/250/500V. 150/300/600V.
PORT SSSP-2	A. C. MILLI-AMMETER	Single	10mA, 50mA.	1.5%
PORT SSSP-2	A.C.VOLTMETER	Single	10V, 15V, 20V, 25V, 50V, 100V, 150V, 300V, 600V.	1.5%
PORT SSSP-3	A.C.AMMETER	Single	0.5A, 1A, 2.5A, 5A, 10A.	1.5%
	A.C.AMMETER	Dual	0.5/1 A. 1/2A. 2.5/5A. 5/10A.
	A.C.VOLTMETER	Single	62.5V, 75V, 125V, 150V, 250V, 300V, 500V, 600V.
		Dual	62.5/125V, 75/150V, 125/250V,150/300V. 250/500V. 300/600V.
		Triple	62.5/125/250V, 75/150/300V, 125/250/500V, 150/300/600V.

MECHANICAL CONSTRUCTION

Size			HOUSING mm	MODEL mm	SCALE		WEIGHT gm. (Approx.)
LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING mm	MODEL mm	LENGTH mm (Approx.)	DIVISIONS	WEIGHT gm. (Approx.)
115	110	50	Polycarbonate	SSSP-	90	30 ~ 50	400

Ordering information

1) Type 2) Model 3) Scale 4)Range 5) Accuracy

Built In Transducer Type Analogue Power Factor Meter

Description / Specification of Built In Transducer Type Analogue Power Factor Meter

We are involved in offering a wide range of Built In Transducer Type Analogue Power Factor Meter to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Built In Transducer Type Analogue Power Factor Meter. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Dynamometric 1Ph And 3Ph Power And Power Factor Meter

DESCRIPTION
Dynamometric instruments are used for measurement of active, reactive & absolute power in 1 Phase & 3 Phase systems for balanced / unbalanced load conditions. Watt, Var & VA instruments incorporate current coils, connected in series with the load & pressure coils connected across the load. These instruments work on "Air cored Electro-Dynamometric" principle. Power Factor meter incorporates two pressure coils, one with non-inductive resistance in series & other with capacitance in series & are cross connected. The deflecting torque produced is proportional to the phase angle between current & voltage vectors. The pointer rests anywhere on the scale when meter is not connected in the circuit, as there is no controlling torque.

FEATURES
•	SCALE	Linear, Side zero or Center zero are available.
•	HOUSING	Sheet Metal (Black painted).
•	TERMINAL PROTECTION	Shrouded terminals to protect from accident, (on request).
•	GLASS	Anti - glare (on request)

ELECTRICAL SPECIFICATIONS
•	TYPE	Dynamometric.
•	OPERATING VOLTAGE	75V to 500V for 1 Ph. 110V / 440V - PT secondary for 3Ph.
	BURDEN	<1.25VA upto 75V, <2.5VA - 100V to 150V, < 5VA - 200V to 300V, <10 VA - 350V to 600V
•	OPERATING CURRENT	0.5A to 10A for 1 Ph. 1A/5A-CT secondary for 3Ph
	BURDEN	<5VA upto 5A, <10VA upto 10A.
•	FREQUENCY	45 ~ 65Hz. (400Hz. on request).
•	ACCURACY	Class 1.5 for Watt / Var / VA. 2° for PF.
•	DIELECTRIC TEST	2kV RMS for 1 minute.
•	OVERLOAD CONTINUOUS	1.2 times
•	OERLOAD SHORT TIME	2 times V_N / 10 times I_N for 5 seconds.
•	OPERATING TEMP.	-10°C to 55°C
•	STORAGE TEMP.	-20°C to 70°C
•	HUMIDITY	up to 95% RH
•	CONFORMS TO	I.S. 1248 / I.E.C. 60051 (Part 3) for WATT / VAR & (Part 5) for PF.

MECHANICAL SPECIFICATIONS
SIZE (mm)	DEPTH (mm)	PANEL CUTOUT (mm)	SCALE LENGTH (mm)	WEIGHT (gms.)
96 x 96 1 ph or 3 ph	See table 1	92 x 92^+0.8	80 (approx.)	See table 2
144 x 144 1ph or 3 ph	See table 1	138 x 138^+1.0	140 (approx.)	See table 2

Table no. 1 (For Depth in mm)

Parameter

WATT METER

VAR METER

VA METER

PF METER

1PH

3P1E

3P2E

3P3E

1PH

3P1E

3P2E

3P3E

1PH

3P1E

3P2E

3P3E

1PH

3P1E

3P2E

3P3E

96 x 96

80

100

-

100

-

80

-

100

-

80

-

144 x 144

85

125

165

-

125

165

85

-

125

165

125

-

Table no. 2 (For Weight in approx. kg)

Parameter

WATT METER

VAR METER

VA METER

PF METER

1PH

3P1E

3P2E

3P3E

1PH

3P1E

3P2E

3P3E

1PH

3P1E

3P2E

3P3E

1PH

3P1E

3P2E

3P3E

96 x 96

0.5

0.7

-

0.7

-

0.5

-

0.8

-

0.6

0.7

-

144 x 144

1.0

1.4

1.7

-

1.4

1.8

-

1.5

1.8

1.2

1.4

-

Note : The connection diagram label is affixed on each meter.

Ordering information

1) Type 2) Size, 3) Parameter, 4) Phase & Element and Range 5) Operating Voltage & PTR
6) Operating Current & CTR.

Built In Transducer Type Digital Power Meter

Description / Specification of Built In Transducer Type Digital Power Meter

We are involved in offering a wide range of Built In Transducer Type Digital Power Meter to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Built In Transducer Type Digital Power Meter. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Portable Instrument 1Ph And 3Ph Power Meter (Large Size Dynamometric In Wodden Housing)

DESCRIPTION

Protable dynamometric types instruments, incorporating single element / two elements or three elements power measurement methods and specially designed to be operated in horizontal position.

FEATURES / ADVANTAGES
•	Instruments with accuracy class 0.5 for 1 Ph Watt, 1.5 for 3Ph, 2° for PF.
•	Instruments with multiple scale available (refer table).
•	Robust housing suitable for schools, workshops and field operations for continuous use.

ELECTRICAL SPECIFICATIONS
TYPE	MODEL		POTENTIAL COIL (A)	CURRENT COIL (A)	ACCURACY
Watt Meter With Low Power Factor	PORT LSDW-1	TPDC	75/150/300,150/300/600	0.5/1,1/2,2.5/5,5/10,10/20	1.5%
WATT METER	PORT LSDW-2	SPSC	75,150,300,600	0.5,1,2,2.5,5,10,20	0.5%
		DPSC	75/150,150/300,300/600
		TPSC	75/150/300,150/300/600
		SPDC	75,150,300,600	0.5/1,1/2,2.5/5,5/10,10/20
		DPDC	75/150,150/300,300/600
		TPDC	75/150/300,150/300/600
	PORT LSDW-3	SPSC	75,150,300,600	0.5,1,2,2.5,5,10,20	1.5%
	PORT LSDW-4	SPSC	75,150,300,600	0.5,1,2,2.5,5,10,20
	PORT LSDW-4	DPDC	75/150,150/300,300/600	0.5/1,1/2,2.5/5,5/10,10/20
	PORT LSDW-5	SPSC	75,150,300,600	0.5, 1, 2, 2.5, 5, 10, 20
	PORT LSDW-5	SPDC	75,150,300,600	0.5/1,1/2,2.5/5,5/10,10/20
VAR METER	PORT LSDW-6	SPSC	75,150,300,600	0.5,1,2,2.5,5,10,20	1.5%
	PORT LSDW-6	DPDC	75/150,150/300,300/600	0.5/1,1/2,2.5/5,5/10,10/20
	PORT LSDW-7	SPSC	75,150,300,600	0.5, 1, 2, 2.5, 5, 10, 20
	PORT LSDW-7	SPDC	75,150,300,600	0.5/1,1/2,2.5/5,5/10,10/20
POWER FACTOR METER	PORT LSDW-8	SPSC	75,150,300,600	0.5,1,2,2.5,5,10,20	2°
		DPSC	75/150,150/300,300/600
		TPSC	75/150/300,150/300/600
		SPDC	75,150,300,600	0.5/1,1/2,2.5/5,5/10,10/20
		DPDC	75/150,150/300,300/600
		TPDC	75/150/300,150/300/600
	PORT LSDW-9	SPSC	75,150,300,600	0.5,1,2,2.5,5,10,20

SELECTION OF RANGES

Upper limit of measuring range for meters shall be one of the following values -

1, 1.2, 1.5, 2, 2.5, 3, 4, 5, 6, 7.5, 8 or their decimal multiples.

Example for selection of proper range

1 ) Formula for 1 Phase active power

P(max) = VI COS¢ Where COS¢ = 1.

If Voltage = 500V & Current = 2.5A calculated power = 500 x 2.5 x 1 = 1.25kW.

If the calculated value is 1.25kW 0 - 1.2kW or 0 - 1.25kW shall be selected as a range for power.

2) Formula for 3 Phase active power with PT & CT.

P(max) = √ 3VI COS¢ x PTR x CTR Where COS ¢ = 1.

If Voltage = 110V & Current = 5A PTR = 400kV/110V CTR = 1000A/5A

calculated power = √ 3 x 110x5 x (400x1000/110) x (1000/5)= 692MW.

If the calculated value is 692MW 0 - 600MW or 0 - 750MW shall be selected as a range for power.

Note :
•	All Wattmeters are calibrated at cos¢ = 1 and Varmeter at sin¢ = 1
•	All Low Power Factor Wattmeters are calibrated at cos¢ = 0.2 lag.
•	Voltage & Current range other than specified can be supplied on request, if feasible.

Mechanical Specifications

Fig. 1	Fig. 2

SIZE	LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING MATERIAL	MODEL IDENTIFICATION	SCALE		WEIGHT kg. (Approx.)
SIZE	LENGTH mm	WIDTH mm	HEIGHT mm	HOUSING MATERIAL	MODEL IDENTIFICATION	LENGHT mm (Approx.)	DIVISIONS	WEIGHT kg. (Approx.)
1	300	200	155/190	Wooden Box	LSDW-	150	100 ~ 150	4 ~ 5
2	225	355	190/225	Wooden Box	LSDW-	150	100 ~ 150	5.5 ~ 7.5

Ordering information

1) Type 2) Model 3) Parameter, Phase, Range 3) Operating Voltage & PTR
4) Operating Current & CTR.

Regular Shunts

DESCRIPTION
The shunts are designed to comply with the requirements of IS1248 / DIN43703 & DIN43780. The shunt provides an accurate d.c. millivolt signal, exactly proportional to the system current

FEATURES
•	Rating 1A to 15000A
•	Riveted and soldered construction
•	In-line bus bar mounting
•	Very low temperature coefficient
•	High overload withstand
•	Shock and vibration Proof
•	Long term stability

•	TYPE 1) Insulated mounting 2) "I" Section 3) "L" Section 4) "T" Section	Ranges 1, 1.5,2,2.5, 3,4,5,6, 10, 15,20,25, 30 Amp. 30, 40, 50, 60, 75, 80, 100, 120, 150Amp. 200, 250, 300, 400, 500, 600, 750, 800, 1000, 1200, 1500, 2000, 2500, 3000Amp. 4000, 5000, 6000, 7500, 8000, 10000, 12000, 15000Amp.
•	ACCURACY	± 0.5%
•	CONTINUOUS OVER LOAD	20% rated current
•	5 SECONDS WITHSTAND	10 times for 1 A to 500 Amp. 5 times for 600A to 2000Amp. 2 times for 2500A to 15000Amp.
•	TEMP. COEFFICIENT	0.002% per °C.
•	AMBIENT TEMP.	Calibration at 23°C.
•	OPERATING TEMP.	-10°C to 55°C.
•	STORAGE TEMP.	-20°C to 70°C
•	MAXIMUM LOAD	The load should not exceed 0.1% of the nominal current rating for specified accuracy.
•	MILLIVOLT	50mV, 60mV, 75mV, l00mV, 150mV, 300mV (standard) Other mV outputs on request.

NOTE :

Two cables of 1 meter length with 1.5mm cross sectional area are provided. This corresponds to a total resistance of 0.026 ohms. The instruments are calibrated with this resistance and consequently the cable length must not be changed. If different length or resistances are required, please indicate while ordering.

INSTALLATION

The best performance is guaranteed if the following points are observed.

1) Shunts may be mounted horizontally or vertically. Horizontal mounting gives the best heat dissipation.

2) Utilize the full end block surface area.

3) Ample ventilation should be provided.

4) Busbar should be adequately rated, cleaned & coated with a thin layer of silicon grease applied to the contact surface area.

5) Bolts and nuts must be carefully tightened.

CAUTION

Shunts are not insulated & protection against accidental contact may be necessary in order to comply with Health & Safety regulations.

Ordering information

1) Current rating 2) Millivolt output 3) Length of the cable

Rated Current Amps.	Dim 'A' Max.					Dim 'B1'	Dim 'B2'	Dim 'B3'	Dim 'C1'	Dim 'E'					Dim 'H'
	(mV)									(mV)					(mV)
	60	75	100	150	300					60	75	100	150	300	60/75	100~300
1~30	90	90	90	90	90	20	-	-	8	80	80	80	80	80	8	8
40~150	100	120	145	225	285	^*20	-	-	8	80	100	125	205	365	8	8
200~300	145	165	190	270	430	30	15	-	10	105	125	150	230	390	30	30
400~750	145	165	190	270	430	40	20	-	10	105	125	150	230	390	30	30
800~1000	165	185	210	290	450	^*60	30	-	10	115	135	160	240	400	30	30
1200~1500	165	185	210	290	450	90	21	48	10	115	135	160	240	400	30	30
1600~3000	165	185	210	290	450	120	30	60	10	115	135	160	240	400	30	60
4000~5000	165	185	220	300	460	120	30	60	15	115	135	170	250	410	60	130
6000~7500	175	195	220	300	460	154	25	52	25	125	145	170	250	410	130	130
8000~10000	185	205	-	-	-	206	25	52	30	135	155	180	260	420	170	-
12000~15000	185	205	-	-	-	310	25	52	30	135	155	180	260	420	170	-

Rated Current Amps.	Current Terminal Dim.	No. of Current Terminal	No. of Current Terminal


1~30	M 5x12	2 x 1	-
40~150	M 8x12	2 x 1	15
200~300	M 12x40	2 x 1	20
400~750	M 16x45	2 x 1	25
800~1000	M 20x50	2 x 1	40
1200~1500	M 16x45	2 x 2	40
1600~3000	M 20x50	2 x 2	40
4000~5000	M 20x50	2 x 2	40
6000~7500	M 20x75	2 x 3	40
8000~10000	M 20x85	2 x 4	40
12000~15000	M 20x85	2 x 6	40


UPTo 30 Amps.	40 A To 150 A	200 A To 1000 A


1200 TO 3000 A	4000 A To 5000A 6000 A to 7500 A shunts have 3 Boltsat each terminal spaced at lateral distance B3	8000 A To 10000 A 12000 A to 15000 A shunts have 6 Bolts at each terminal spaced at lateral distance B3


	8000 A To 10000 A 12000 A to 15000 A shunts have 6 Bolts at each terminal spaced at lateral distance B3
(All Dimension are in mm)

Note :

1) Dimension A, E, H are the same for 50mV shunt & 60mV shunt.

2) Unless specified tolerance for mounting dimensions (Dim "E") shall be of ±1.5mm upto 1500A rating & ± 2.0mm for the rating above 1500A.

3) Maximum value of 'H' is specified, Minimum value is equal to corresponding value of 'C1'.

4) ^*Dimension 20 & 60mm is for 60/75mV and 25 & 70 mm respectively for 100~300mV.

5) The consumption of measuring instusments should not exceed 500 microwatts for interchangeable shunts.

New t Series Single Phase Transducer

Description / Specification of New t Series Single Phase Transducer

We are involved in offering a wide range of New t Series Single Phase Transducer to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of New t Series Single Phase Transducer. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Power Line Transducers

DESCRIPTION

AE transducers convert various electrical power line parameters viz. Voltage, Current, Frequency, Power Factor, Active power, Reactive power, Apparent power into load independent DC current or voltage output. These are used in various electrical, thermal, chemical & other power plants to monitor processed data either locally or remotely, using various devices such as indicating meters, data loggers, recorders, SCADA systems.

FEATURES
•	Open & short circuit protected.
•	Current and Voltage output are indendent of load impedance.
•	Measurement of DC parameters.

ELECTRICAL SPECIFICATIONS
•	TYPE	Ohm, DC / AC Voltage, DC / AC Current, Frequency, Summation, Power Factor, DC / AC Watt, Var, VA Transducers.
•	INPUT RANGE
	VOLTAGE	0 - 500V DC / 0 - 500V AC.
	CURRENT	0 - 5A DC (for higher ranges 50 - 300mV ext. Shunt) / 0 - 5A AC.
	FREQUENCY	50 / 60Hz ± 5hz., 400hz ± 20Hz. (other Frequency on request).
	POWER FACTOR	0.5% (lag) - unity - 0.5(lead). (Refer Note 4)
	RESISTANCE	0 - 500Ω for Ohm Transducer
•	ACCURACY	0.5% of f.s.d. for Ohm, Voltage, Current, Summation, Power Factor, Watt, Var, VA Transducers. For Frequency Transducer - 0.2% of Centre frequency.
•	AUX. SUPPLY	63.5V, 110V, 220V, 230V, 240V, 380V, 415V, 440V AC ±10%, 50/60Hz. 24V, 48V, 110V, 220V DC ±10%
•	VA BURDEN	For VOLTAGE ≤ 1.0, For CURRENT ≤ 0.5, for AUX Supply ≤ 4.0
•	OUTPUT RANGE
	CURRENT MAX. LOAD	0 - 1mA	0- 5mA	0 - 10mA	0 - 20mA	4 - 20mA	10 - 0 - 10mA.
		10kΩ	2kΩ	1kΩ	500Ω	500Ω	1kΩ
	VOLTAGE MIN. LOAD	0 - 1V	0 - 5V	0 - 10V	1 - 5V	2 - 10V	10 - 0 10V
		500Ω	2.5Ω	5kΩ	2.5kΩ	5kΩ	5kΩ
•	RIPPLE	Maximum 0.5% of span.
•	OVERLOAD CAPACITY
	• VOLTAGE continuous		120% of nominal
	short term(10sec)		150% of nominal
	• CURRENT continuous		120% of nominal
	short term(3 sec)		10 times of nominal
•	RESPONSE TIME	300 msec.
•	OPEN CKT. VOLTAGE	22 Vmax.
•	IMPULSE VOLTAGE	Peak Voltage of 5kV, Standardized impulsed waveform of 1.2 / 50µsec.
•	INSUL^NRESISTANCE	Greater than 20 Mohms at 500V DC
•	DIELECTRIC TEST	2kV RMS for 1 minute (4kV on request)
•	OPERATING TEMP.	0°C to 55°C
•	STORAGE TEMP.	-20°C to 70°C
•	HUMIDITY	Upto 95% RH
•	CONFORMS TO	I.S.12784 (Part 1)/ I.E.C. 688

MECHANICAL SPECIFICATION		Transducers Panel Cum Din Rail Mounting
		Mounting Rail EN 50022

2 mounting holes φ4.5mm for M4, 40 ~ 50 mm OR Equivalent screw	M3 x 15 mm screw 4 terminals in 2 rows Lug width 6.0 ~ 6.4 mm	4 mounting holes Ø 5mm For M4, 20 ~ 25mm OR Equivalent screw	M3 X 10mm screw 8 Terminals in 2 Rows

MODEL	PD1	PD2	PD3*
HEIGHT	H = 123 mm	H = 80mm	H = 115 mm
AUX. SUPPLY	AC / DC Auxiliary	AC Auxiliary*	DC Auxiliary
Type	Ohm Transducer	Summation Transducer
	DC Voltage Transducer	Single Phase Power Factor Transducer
	DC Current Transducer	3 Phase Single Element Power Factor Transducer
	Frequency Transducer	Unipolar output	Bipolar output*
	AC Voltage Transducer	3 Phase 2 Element Watt / Var / VA Transducer*
	AC Current Transducer	3 Phase 3 Element Watt / Var / VA Transducer*

*TYPE

3 Phase 2 Elemet & 3 Phase 3 Element Watt or Var Transducers with AC Auxiliary supply and Bipolar output are available in MODEL PD3.

Note :
1)	Self - Powered AC Voltage, Current, Frequency , PF & Power Transducers are available on request.
	Self - Powered Voltage & Current transducers operate for input variation between 10% to 120% of the range.
	Self - Powered Frequency, Power and Power Factor Transducers operate on ±10% of rated voltage.
2)	The individual output, in dual output transducers, are not isolated from each other.
3)	Summation Transducers Maximum Inputs - 5 nos.; No isolation between any two inputs & between input & output.
4)	Output of power factor transducers is proportional to phase angle.

Ordering information
1)Type 2) Model 3) Input Range 4 a) Output Range (Current / Voltage ) 4 b) Single or dual 5) Aux. Supply

ADDITIONAL INFORMATION
•	Power & Power Factor	1) Voltage (PTR) 2)Frequency 3) Current (CTR)
•	Summation	1) No. of inputs

Programmable Multifunction Transducer (Pmt 9)

Description / Specification of Programmable Multifunction Transducer (Pmt 9)

We are involved in offering a wide range of Programmable Multifunction Transducer (Pmt 9) to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Programmable Multifunction Transducer (Pmt 9). Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

High Tension Resin Cast Indoor Potential Transformers

DESCRIPTION
Direct measurement of Voltage in high voltage system is not possible because of insulation problem of measuring instruments. It is also not possible to use voltage flowing through the system directly for protection purpose due to its high value and high insulation problem. In such conditions Voltage Transformers are used.

BASIC FUNCTIONS OF VOLTAGE TRANSFORMERS ARE . . .
•	To reduce the line voltage to a value which is suitable for standard measuring instruments, relays etc.
•	To isolate the Measuring Instruments, Meters, Relays etc. from high voltage side of an installation.
•	To sense abnormalities in voltage & give voltage signals to protective relays to isolate the defective system.

FEATURES

The transformers are vacuum encapsulated in epoxy resin, which ensures faultless insulation. Incombustible high-class raw material, together with uniform cast resin bodies, gives the voltage transformers a high mechanical & electrical strength that requires no maintenance. It is advisable to protect the transformers from direct sunlight & access to dust.

ELECTRICAL SPECIFICATIONS
•	TYPE	Single Pole Insulated & Double Pole Insulated.
•	OPERATING VOLTAGE	Single Pole Insulated 1.1kV, 2.2kV, 3.3kV, 6.6kV, 11kV, 22kV, 33kV.
		Double Pole Insulated 1.1kV, 2.2kV, 3.3kV, 6.6kV, 11kV.
•	SECONDARY VOLTAGE	110V, 110 1√3,110V / 3 (others on request).
•	RATED BURDEN	50VA, 100VA, 150VA, 200VA (others on request).
•	ACCURACY CLASS	0.2, 0.5, 1.0, 3.0, 3P, 6P.
•	FREQUENCY	50Hz.
•	OPERATING TEMP.	-10° C to 40° C.
•	SYSTEM CONDITION	Earthed, Unearthed.
•	CONFORMS TO	I.E.C. 186, I.E.C. 60044-2, IS 3156.

MECHANICAL CONSTRUCTION

Fig. No. 1	Fig. No. 2

Ordering information

While ordering mention all the Electrical specification required.

High Tension Resin Cast Indoor Current Transformers

DESCRIPTION
Direct measurement of Current in high voltage system is not possible because of insulation problem of measuring instruments. It is also not possible to use current flowing through the system directly for protection purpose due to its high value and high insulation problem. In such conditions Current Transformers are used.

BASIC FUNCTIONS OF CURENT TRANSFORMERS ARE
•	To reduce the line current to a value which is suitable for standard measuring instruments, relays etc.
•	To isolate the Measuring Instruments, Meters, Relays etc. from high voltage side of an installation.
•	To protect Measuring Instruments against short circuit currents.
•	To sense abnormalities in current & give current signals to protective relays to isolate the defective system.

FEATURES

The transformers are vacuum encapsulated in epoxy resin, which ensures faultless insulation. Incombustible high-class raw material, together with uniform cast resin bodies, gives the current transformers a high mechanical & electrical strength that requires no maintenance. It is advisable to protect the transformers from direct sunlight & access to dust.

ELECTRICAL SPECIFICATIONS
•	TYPE	Wound & Ring type
•	OPERATING VOLTAGE	1.1kV, 2.2kV, 3.3kV, 6.6kV, 11kV, 22kV, 33kV.
•	PRIMARY CURRENT	Upto 2500 Amps. In Wound Type From 300A to 3000A in Ring Type
•	PRIMARY CURRENT
•	SECONDARY CURRENT	5A & 1A (Others on Request)
•	SHORT TIME THERMAL CURRENT & IT'S DURATION	Upto 40kA for 1 second (Others on Request)
•	SHORT TIME THERMAL CURRENT & IT'S DURATION	Upto 40kA for 1 second (Others on Request)
•	RATED BURDEN	5,10,15,20, and 30VA (Others on Request)
•	ACCURACY CLASS	0.2, 0.5, 1.0, 5P10, 5P15.
		(For differential protection, REF protection, Bus Bar
		protection, CT with accuracy class PS can be offered.)
•	FREQUENCY	50Hz.
•	OPERATING TEMP.	-10°C to 40°C.
•	CONFORMS TO	I.E.C. 185, I.E.C. 44-1, IS 2705.

MECHANICAL CONSTRUCTION

Fig.No. - Wound Type

Fig. No. - Ring Type

Ordering information

While ordering mention all the Electrical Specification required.

Note : for class PS accuracy, please specify formula for knee-point voltage for design optimisation

High Tension Oil Cooled Outdoor Potential Transformers

DESCRIPTION

Direct measurement of Voltage in high voltage system is not possible because of insulation problem of measuring instruments. It is also not possible to use voltage through the system directly for protection purpose due to its high value & high insulation problem. In such conditions voltage transformers are used.

BASIC FUNCTIONS OF VOLTAGE TRANSFORMERS ARE ...
•	To reduce the line voltage to a value which is suitable for standard measuring instruments, relays etc.
•	To isolate the Measuring Instruments, Meters, Relays etc. from high voltage side of an installation.
•	To sense abnormalities in Voltage & give Voltage signals to protective relays to isolate the defective system.

FEATURES

The transformers are oil filled, assembled in M.S.Tanks & Chambers together with suitable Porcelain Bushing. High quality C.R.G.O. Silicon Steel is used in the transformer. High quality kraft & crepe insulating paper is used to build up main insulation. Semiconducting shield is used to give linear distribution of Electrical stress along the length of the bushing. Filtered & de-aerated EHV grade oil is filled in VTs while VT is under vacuum. To seal it, the space left for expansion on the top is filled with dry & pure Nitrogen through non returnable valve at pre-determined pressure.
Design incorporating Stainless Steel Bellows instead of Nitrogen cushioning is also available.

ELECTRICAL SPECIFICATIONS
•	TYPE	Single Pole Insulated & Double Pole Insulated.
•	OPERATING VOLTAGE	Single Pole Insulated 1 lkV, 22kV, 33kV, 66kV, 11OkV, 132 kV, 220kV.
		Double Pole Insulated llkV, 22kV, 33kV.
•	SECONDARY VOLTAGE	110V, 110V~3,,,,,, 110V/ 3 (others on request)
•	BURDEN	50VA,100VA,150VA,200VA (others on request)
•	ACCURACY	0.2, 0.5, 1.0, 3.0, 3P,6P.
•	FREQUENCY	50 Hz.
•	OPERATING TEMP.	-10°Cto40°C
•	SYSTEM CONDITION	Earthed, Unearthed.
•	CONFORMSTO	IEC186,IEC60044-2,IS3156.

MECHANICAL CONSTRUCTION

66kV VT

Ordering information

While ordering mention all the Electrical Specification required.

High Tension Oil Cooled Outdoor Current Transformers

DESCRIPTION

Direct measurement of current in high voltage system is not possible because of insulation problem of measuring instruments. It is also not possible to use current flowing through the system directly, for protection purpose due to its high value & high insulation problem. In such conditions Current Transformers are used.

BASIC FUNCTIONS OF CURRENT TRANSFORMERS ARE ...
•	To reduce the line current to a value which is suitable for standard Measuring Instruments, Relays etc.
•	To isolate the Measuring Instruments, Meters, Relays etc. from high voltage side of an installation.
•	To protect Measuring Instruments against short circuit currents.
•	To sense abnormalities in current & give current signals to protective relays to isolate the defective system.

FEATURES

The transformers are oil filled, assembled in M.S.Tanks & Chambers together with suitable Porcelain Bushing. High quality C.R.G.O. Silicon Steel is used in the transformer. High quality crepe insulating paper is used to build up main insulation. Semiconducting shield is used to give linear distribution of Electric stress along the length of the bushing. Filtered & de-aerated EHV grade oil is filled in CTs while CT is under vaccum. To seal it, the space left for expansion on the top is filled with dry & pure Nitrogen through non returnable valve at pre-determined pressure.

ELECTRICAL SPECIFICATIONS
•	TYPE	Live or Dead Tank
•	OPERATING VOLTAGE	11kV, 22kV, 33kV, 66kV, 110kV, 132 kV, 220kV, 400 kV.
•	PRIMARY CURRENT	Upto 2500 Amps.
•	SECONDARY CURRENT	5A & 1A (Others on request).
•	SHORT TIME THERMAL CURRENT & ITS DURATION	Upto 40kA for 1 second (Others on request).
•	SHORT TIME THERMAL CURRENT & ITS DURATION	Upto 40kA for 1 second (Others on request).
•	RATED BURDEN	5,10,15,20, 30VA (Others on request)
•	ACCURACY CLASS	0.2, 0.5, 1 .0, 5P10, 5P15 (Others on request) (For differential protection, REF protection, Bus Bar protection, CT with accuracy class PS can be offered.)


•	FREQUENCY	50Hz.
•	OPERATING TEMP.	-10°C to 40°C
•	CONFORMS TO	IEC -185 / IEC - 44 -1 / IS - 2705.

MECHANICAL CONSTRUCTION

132kV Dead Tank CT	66kV Live Tank CT

Ordering information

While ordering mention all the Electrical Specification required.

Note : For class PS accuracy, please specify formula for knee - point voltage for design optimisation.

Combimeter Digital Vif Meter

Description / Specification of Combimeter Digital Vif Meter

We are involved in offering a wide range of Combimeter Digital Vif Meter to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Combimeter Digital Vif Meter. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Vif Meter Single And Three Phase

Description / Specification of Vif Meter Single And Three Phase

We are involved in offering a wide range of Vif Meter Single And Three Phase to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Vif Meter Single And Three Phase. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Analogue Panel Voltmeter With Built In Selector Switch

Description / Specification of Analogue Panel Voltmeter With Built In Selector Switch

We are involved in offering a wide range of Analogue Panel Voltmeter With Built In Selector Switch to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of Analogue Panel Voltmeter With Built In Selector Switch. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Static Watthour Meter With Electro Mechanical Display

DESCRIPTION
It measures the energy (Watt - Hour) consumed by the load.

FEATURES
•	True RMS measurement.
•	Isolated Soild - State Pulse Output Or built - in RS - 485 interface for communication with PC.
•	Reverse direction indication.
•	Tamper - proof
•	Battery Backup facility to retain the data for six months. (only for kWh meter having in-built RS- 485

ELECTRICAL SPECIFICATIONS
•	WIRING METHOD	Single Phase
		3 Phase 3 Element 4 Wire,
		3 Phase 2 Element 3 Wire.
•	OPERATING VOLTAGE (RANGE)	110V Line voltage (85 to 130V)
		240V Phase Voltage (180V to 270V)
		415 Line Voltage (330V to 470V)
•	OPERATING CURRENT (RANGE)	1Amp (0.05 to 1.2 Amps)
•	OPERATING CURRENT (RANGE)	5Amps (0.25A to 6Amps)
•	SIGNAL FREQUENCY	45Hz TI 55Hz
•	OPERATING POWER FACTOR	0.5 (Lag) - Unity - 0.8 (Lead)
•	ACCURACY	1.0%
•	AUX. SUPPLY	110V / 240V AC ±10%, 45Hz to 55Hz
•	VA BURDEN (RATED)	Voltage : 0.5 VA / Phase
		Current : 0.5 VA / Phase
		Aux. Supply : 3VA
•	DISPLAY	6 Digit Mechanical Counter, Tamper proof, Non-resettable.
•	PULSE OUTPUT	500 ± 50m sec. (ON period)
•	CONTACT RATING	24VDC, 100mA DC
•	INTERFACE	RS 485
•	INSULATING RESISTANCE	5 Mohms at 500VDC
•	DIELECTRIC STRENGTH	2kV RMS for 1minute
•	OPERATING TEMP.	0° C to 55° C
•	STORAGE TEMP.	-10° C to 70° C
•	HUMIDITY	Upto 95% RH
•	CONFORMS TO	I.S 13779

MECHANICAL SPECIFICATIONS
•	SIZE	96 x 96 x 130mm
•	WEIGHT	870gms. Approx.

Ordering information

1) Wiring method 2) Operating Voltage 3) Operating Current 4) PT Ratio 5) CT Ratio Aux. Supply

Static Watthour Meter With Led Display

DESCRIPTION
It measures the energy (Watt - Hour) consumed by the load.

FEATURES
•	True RMS measurement.
•	Isolated Soild - State Pulse Output Or built - in RS - 485 interface for communication with PC.
•	Reverse direction indication.
•	Tamper - proof
•	Battery Backup facility to retain the data for six months. (only for kWh meter having in-built RS- 485

ELECTRICAL SPECIFICATIONS
•	WIRING METHOD	Single Phase
		3 Phase 3 Element 4 Wire,
		3 Phase 2 Element 3 Wire.
•	OPERATING VOLTAGE (RANGE)	110V Line voltage (85 to 130V)
		240V Phase Voltage (180V to 270V)
		415 Line Voltage (330V to 470V)
•	OPERATING CURRENT (RANGE)	1Amp (0.05 to 1.2 Amps)
•	OPERATING CURRENT (RANGE)	5Amps (0.25A to 6Amps)
•	SIGNAL FREQUENCY	45Hz TI 55Hz
•	OPERATING POWER FACTOR	0.5 (Lag) - Unity - 0.8 (Lead)
•	ACCURACY	1.0%
•	AUX. SUPPLY	110V / 240V AC ±10%, 45Hz to 55Hz
•	VA BURDEN (RATED)	Voltage : 0.5 VA / Phase
		Current : 0.5 VA / Phase
		Aux. Supply : 3VA
•	DISPLAY	6 Digit Mechanical Counter, Tamper proof, Non-resettable.
•	PULSE OUTPUT	500 ± 50m sec. (ON period)
•	CONTACT RATING	24VDC, 100mA DC
•	INTERFACE	RS 485
•	INSULATING RESISTANCE	5 Mohms at 500VDC
•	DIELECTRIC STRENGTH	2kV RMS for 1minute
•	OPERATING TEMP.	0° C to 55° C
•	STORAGE TEMP.	-10° C to 70° C
•	HUMIDITY	Upto 95% RH
•	CONFORMS TO	I.S 13779

MECHANICAL SPECIFICATIONS
•	SIZE	96 x 96 x 130mm
•	WEIGHT	870gms. Approx.

Ordering information

1) Wiring method 2) Operating Voltage 3) Operating Current 4) PT Ratio 5) CT Ratio Aux. Supply

D.C. Energy Meters

Description / Specification of D.C. Energy Meters

We are involved in offering a wide range of D.C. Energy Meters to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of D.C. Energy Meters. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

K.W.H. Energy Meters

Description / Specification of K.W.H. Energy Meters

We are involved in offering a wide range of K.W.H. Energy Meters to our most valued clients. Our range of these are widely appreciated by our clients which are situated all round the nation. We offer our range of it at most affordable prices.

We introduce ourselves as an eminent trader and supplier of an extensive array of K.W.H. Energy Meters. Prior to dispatch, our quality controllers run numerous tests on the entire range on various parameters of quality and durability. The offered equipment is manufactured using superior quality components with the aid of sophisticated techniques at the vendors' end. Moreover, our precious clients can purchase it in different technical specifications at reasonable price from us within promised time frame.
Features:

Sturdy design
Highly durable
Application specific design

Featured Products

Welcome to AUTOMATIC ELECTRIC LTD.

C.T. Testing Unit

H.V. Tester From 2.5 To 200 Kv

P.T. Testing Unit

Current Transformer

Voltage Transformer

Encapsulated Current Transformers Ae 110 (86) Series

Encapsulated Current Transformers Ae 125 (104) Series

Encapsulated Current Transformers Ae 65 (45) Series

Encapsulated Current Transformers Ae 78 (62) Series

Encapsulatedcurrent Transformers Ae 155 (140) Series

Encapsulated Current Transformers Ae 70 (50) Series

Encapsulated Current Transformers Ae 98 (74) Series

Low Tension Current Transformers

Low Tension Indoor Medium Voltage Epoxy Resin Cast Current And Voltage Transformers Details Part 2

Dimmerstat Continuously Variable Voltage Auto Transformer

Current Injection Test Unit

Step Syn A.C. Synchronous Motor

Rectifier Units For Electroplating And Anodising

Lighting Transformer Resin Cast Upto 630Kva

Ultra Isolation Transformer

Ac Voltage Stabilizers

Automatic Voltage Stabilizers

Test Bench Unit

Low Tension Power Transformer

Digital Panel 16 Range Ammeters

Digital Power Factor Meter

True Rms Onsite Programmable Digital Panel Ammeter

True Rms Onsite Programmable Digital Panel Voltmeter

Dc Energy Meter

Digital Energy Meter (Counter Type)

Digital Energy Meter (Led Display And Rs 485 Interface)

Electronic Led Frequency Meter

Vibrating Reed Frequency Meter

Dual Kwh Meter

Maximum Demand Controller Mdc 1000

Phase Sequence Indicator

Portable Instrument Multi Range And Multi Parameter (Medium Size Multi Range With Bakelite Housing)

Synchroscope

Moving Coil 240 Long Scale Instruments

Moving Coil Ammeters And Voltmeters (Slide In Scale)

Moving Iron Ammeters And Voltmeters (Slide I Scale)

Maximum Demand Meter

Multi Function Meter Ae90xx With Dg Monitor And Printer

Multifunction Meter Ae9000 Ae9001 Ae9002 Ae9003 Part I

Multifunction Meter Ae9000 Ae9001 Ae9002 Ae9003 Part Ii

Multifunction Meter Ae9000 With Thd Measurement

Portable Instrument 1Ph And 3Ph Power Factor Meter (Large Size Dynamometric In Wodden Housing)

Portable Instrument D.C. And A.C. Ammeters (Large Size Precision In Wodden Housing)

Portable Instrument D.C. And A.C. Ammeters (Medium Size Standard With Bake Lite Housing)

Portable Instrument D.C. And A.C. Ammeters (Small Size Standard With Polycarbonate Housing)

Portable Instrument D.C. And A.C. Voltmeters (Large Size Precision In Wodden Housing)

Portable Instrument D.C. And A.C. Voltmeters (Medium Size Standard With Bake Lite Housing)

Portable Instrument D.C. And A.C. Voltmeters (Small Size Standard With Polycarbonate Housing)

Built In Transducer Type Analogue Power Factor Meter

Dynamometric 1Ph And 3Ph Power And Power Factor Meter

Built In Transducer Type Digital Power Meter

Portable Instrument 1Ph And 3Ph Power Meter (Large Size Dynamometric In Wodden Housing)

Regular Shunts

New t Series Single Phase Transducer

Power Line Transducers

Programmable Multifunction Transducer (Pmt 9)

High Tension Resin Cast Indoor Potential Transformers

High Tension Resin Cast Indoor Current Transformers

High Tension Oil Cooled Outdoor Potential Transformers

High Tension Oil Cooled Outdoor Current Transformers

Combimeter Digital Vif Meter

Vif Meter Single And Three Phase

Analogue Panel Voltmeter With Built In Selector Switch

Static Watthour Meter With Electro Mechanical Display

Static Watthour Meter With Led Display

D.C. Energy Meters

K.W.H. Energy Meters

Our Vision