The Colloid Mill can be used as in line unit ( Horizontal execution) for the continuous operation in a process line, or with a funnel & circulation line ( Vertical execution).

The Colloid Mill has a broad application range & is used in the Food, Pharmaceutical, Chemical & Cosmetic Industries & even in water treatment plants. It operates successfully for products, which must be ground & well dispersed. It disintegrates particles faster & uniform swiveling without forming of agglomerates & for the homogenizing of products in one pass.

The Mill develops not only hydraulic high pressure in the grinding tool section. but turbulence & cavitations which, then combined provide both a gentle grinding & the required impact, squeezing, cutting etc. Effects for the homogenizing of products & wetting out of powders, all in one pass.

The centrifugal force of the rotor brings the material inside the mill. The rotor & stator combination with its exceptional large surface area provide both a gentle grinding & the required impact effect. A two way valve at the discharge connection of the Colloid Mill can either the processed material to inlet opening for rework or discharge the processed material. 

Safety Features:

All belts, pulleys & transmission system are adequately guarded with suitable covers.

Machine can't be started if the top lid is open due to a proximity sensor.

Machine can't be started if the air pressure is below the set value

Machine can't be started if the discharge flange is open for cleaning due to a proximity sensor.

If main impeller is lifted upward fir cleaning or for visual inspection during validation of cleaning. the machine can't be switched ON.

Machine can't be started unless Fluid bed trolley is kept underneath discharge assembly.

The following additional features can be given with the machine at an extra cost if required.

Main impeller can be lifted by hydraulic cylinder by 100 mm during washing. Using this feature main impeller gets lifted up by a hydraulic cylinder by actuating an electric switch so that cleaning & visual inspection for validation process for the main impeller cleaning can be done easily. See drawing attached to understand this feature.

Automation of RMG operation by means of Programmable Logic Controller (PLC). Details are attached herewith for your reference. We can also do PC based automation.

CIP wash system or clean in process system can be supplied which can be either PLC or manual depending upon the user's requirement. FR washing principal (similar to domestic washing machine for clothes) ensures that bottom side of each bland of main impeller is cleaned properly during wash cycle.

Machine with mechanical seals to enable vacuum loading of material.

Jacketed vessel for heating/ cooling. Solvent recovery can be done by a separate condenser.

Binder solution adding arrangement with triclover fitted for easy removal. The same arrangement can be utilized for CIP wash.

We can provide variable speed drive (AC drive ) for main & chopper impellers where by as per program both impellers will run at the set speed. With this drive one can achieve any rpm at between 50 to 4500 to meet the requirement of any formulation composition.

Main drive can be made to run on hydraulic motor so that main impeller RPM can be varied infinitely. With this & a tilting provision the high shear mixer can be used as a single pot processor where with mechanical seals vacuum drying of the wet mass can be done. Hydraulic tilting of entire bowl from 300o on either side with hot purging enables quicker drying. 

Working Cycle:

Dry Mixing -2 to 4 minutes

Wet Granulation - 4 to 15 minutes.

Discharge - 30 to 60 seconds

Complete Cycle - 6 to 20 minutes.

Raw material are charged as a batch & is subjected to indirect heating while undergoing rotary action. The conical shape of the dryer ensures efficient circulation of hot liquid heating media. The drying operation is being at low temperature under vacuum, that is why it is economical & effective for drying pharmaceuticals, temperature sensitive or easily oxidizable products. When the solvent is present in the wet powders, the recovery of solvent is easily possible. 

Drying take place when the dryer is heated from outside through jacket & vacuum is applied from inside. The drying operation is based on the principal that water or other volatile product moves from a zone of high vapour pressure to a zone of low pressure. This is accomplished by warming the product to be dried to raise the vapour pressure of the absorbed or free liquid, by decreasing the vapour pressure of the gas by vacuum, or by sweeping it away with an air current. Thus the essential conditions for effective drying are efficient & uniform heat transfer throughout the batch & rapid removal of the vapors.

The dryers are designed to meet customer's requirements flexibly & efficiently.

Material of construction : AISI304-304L/316-316L

We provide Quality Documents like D.Q / I.Q./ O. Q. & Operation Manuals with all test Certificates. We Also provide test & calibration certificates with each instrument & traceability to National & International standards.

Low temperature drying under the state - of - vacuum inside.

Very High efficient for uniform drying in a short time as co-efficient of thermal transmission is high.

Dryer can be used for mixing / blending in its single unit.

Solvent recovery can be carried out

Specially designed micro air filter can be provided on receiver while breaking vacuum for safety operation.

Easy to clean.

The discharge of the dried material is easy due to the conical configuration of the dryer & it is possible to fix vibrator.

Nitrogen purging system is available for mechanical seal as well as for cleaning filter.

Specially designed S.S Rotary union is available for hot liquid inlet & outlet.

A self - cleaning butterfly discharge valve

Mode of heating is indirect through steam / hot water or hot oil.

Internal cartridge filter for fine powders with effective surface area.

Available in STD / GMP / cGMP / GAMP / GLP / GCP & LAB models

Ease of inspection & easy to clean with the large optional inspection port door.

One or Two chopper units inside the drying chamber provided for breaking up lumps of the product.

Product sensor / sample nozzle with valve can be provided on charging port.

Internal mechanical seal can be easily detached & removed.

We provide mechanical seal from external side for easy maintenance purpose.

We also provide mechanical seal even for smaller units.

Water heating system or Thermic Fluid (Oil) heating system can be provide for heating / cooling of the main dryer

The complete drive, Nitrogen purging system with vessel & spur pinion are housed in the side 'A' shaped stand imparting a cGMP finish to the dryer. no moving parts of drive & gears are visible from out side. 

Available from 50 lits to 300 lits capacity

Paste preparation kettle is a semi-hemispherical jacketed bowl having two shaft extensions exactly opposite, which are fixed in Plummer block bearings. This jacketed bowl has connection for steam inlet/drain & also for steam pressure. When electric heating is to be used this jacket is filled with oil & that is heated by electric heater dipped inside the jacket.

Depending upon the user requirement, paste preparation kettle has anchor or stirring.

On the shaft extension of paste kettle, there is a worm & worm wheel which is turned rotation for the paste kettle when someone wants to empty the kettle.

Water is put inside the paste kettle bowl for heating & after it gets heated, starch or other binders are added to make a binder or paste. This paste is to be then used for wet granulation process in equipments like high shear mixers (RMG) or in Fluid bed granulators.

Entire construction in S.S.

Semi hemispherical bowl ensure that entire bowl can be emptied by rotating the worm wheel.

Simplified construction enables ease of operation.

Steam or electric heating is possible depending upon the user requirement.

when used with stirrer / anchor the movement of anchor is forward & reserve using cyclic timer. Stirrer ca be supplied at additional cost.

When supplied with stirrer, there is a top entry drive without using any 'V' belt. Stirrer can also be removed for cleaning.

Temperature indication is possible at additional cost. 

Zero hold up ( Reverse flow ) sparkler filter.

Zero fold up sparkler filters work on reveres flow principle & are used for crystal clear filtration by filtering particles up 1 micron size.

Compete filtration of the batch without any holdup due to reveres flow of liquid hence large saving in time & cost.

Back wash facility can be provide for continuous operations.

SS jacket can be provided for hot filtration.

No. scavenger arrangement required.

The cake, filter aid & solids remain totally enclosed allowing filtration of toxic, hazardous & explosive liquids.

No contamination of internal surface of shell.

GMP / cGMP design.

( Reverse Flow Type)

Fittings : A standard filter comes with inlet, outlet, pressure guage, bypass, safety valve, sampler, pump & ss trolley.

Operating Pressure : 3 to 5 Kg/Cm3

Maximum Working : 100o- 200o C ( Depending on filter media)

Note: The flow rate mentioned is in terms of water with 5% carbon & filter to poly propylene paper. Filtration rate may change depending on viscosity of liquids, quality of filter media & nature of solids in liquid be filtered.

The range of S.S Sparkler type filters ensures precisely the right filtration characteristics for all application in Chemical, Pharmaceutical, & Beverages, Distilleries & Food Industries. It is manufactured from AISI 304-304L / 316-316L quality. All joints are argon arc welded & polished to mirror finish.

Type of pump depends upon the Chemical & physical properties of the liquid to be filtered. All necessary connection i.e. pressure gauge, safety valve & air vent valve are provided. Cartridge consists of horizontally arranged filter plates, perforated supporting screens, interlocking cups, center rod, tie rods & filter media. Sample taking device can be provided.

For hot filtration AISI 304/316 jacket id provided to shell circulating heating media. Complete unit is mounted on S.S. trolley & fitted with castor wheels for easy movement. The filter press is generally used to obtain clear filtrate. Specially designed scavenger plate for complete filtration are provided 18" & above models. If required actual testing carried out works, for which, require quality of liquid would be arranged by the customer: otherwise testing can be carried out with water & insoluble carbon/ high flow.

The unfiltered liquid is fed into filter under positive pressure, where liquid travel in downward direction & finds its way through opening on side of the filter plates.

As the liquid pressure increase, the filter media holds the foreign particles & allows only clear filtrate to pass through the central channel formed by interlocking pressure cups to the outlet. Filtration is continued until rate becomes too slow due to cake resistance. 

We provide quality documents like (DQ, IQ,OQ & Operation manuals with all test certificates. We also provide test & calibration certificates with each instrument & traceability to National & International standards.

Filtration rate depends on viscosity of liquids, quality of filter papers/ media & nature of sediments in liquids to be filtered for 24" & above dia filter press, pump & motor are mounted on separate trolleys

Output mentioned is in term of water type liquid having sp. Gr. 1.0 & activated carbon loading 5 kgs/ m2 filtering area.

Very versatile process equipment for uniform & efficient drying of products.

Fully automatic operation based on PLC control / without PLC control.

Minimum handling & more hygienic.

Lifting & tilting device of product container for easy handling

FLP models available as option 

Intrinsically safe earthing arrangements.

Stainless steel interconnecting duct line with flanges for connecting remote mounted heating & fan motor modules

Bucket type bottom chamber above ground level.

Option-steam heated or electric heated blower.

CGMP model with documentation (IQ, DQ, PQ, OQ) as option

PLM is an ideal for the products fo different viscosities, densities, shapes & proportions. The major use includes the production of latexes, adhesives, personal care & cleaning products, dispersion & micro- dispersion of chemical & agricultural pesticide formulations. It is suitable for mixing / blending powders as well as through mixing of ointments, creams, lotions, toothpastes, resins, slurries, ceramics, colour, pigments, rubber & other compounds etc. 

PLM is consists of a single blade or double blade with a high dispersion blade ( Emulsifier/Homogenizer). Intimate & homogenizer mixing of products is achieved by planetary motion of beaters & centrally located high speed dispersion blade for vacuum jacketed mixer unit. The PLM consists of two open beaters moving in planetary motion, scraper blade & centrally located high speed homogenizer run by a separate motor to manufacture ointments, creams, suspensions etc. 

It is a stator- rotor high shear mixer. High speed, high shear & higher power are the main characteristics of stator-rotor mixing device. The high shear action creates a forced product flow. The interchangeability of homogenizer blades are possible to suit the mixing requirements of various products. They are used in many process operations like homogenization, dispersion, emulsification, grinding, dissolving, chemical reaction, cell disruption & coagulation.

PLM is also used for blending, mixing & homogenizing powders of various bulk densities by rectangular shaped or heart shaped ( smaller sized mixers) beaters.

All contact parts- AISI-304 or 316, 304L or 316L

Jacketed bowls can be provided for heating/ cooling of products during mixing.

Bowl mounted on castor wheels for easy mobility.

Provision to mix products under vacuum for de-aireation purpose.

Mechanical seal is provided instead of stuffing box for shaft sealing for vacuum operation.

Teflon scrappers are provided to avoid localized heating or cooling & ensure uniform mixing.

Top drive & agitator assembly can be lifted & lowered by motorized as well as hydraulic system.

Smaller version of Planetary Mixers are provide with lifting arrangement for the bowl instead of top drive & agitator assembly.

Pneumatic system is also available for lifting & lowering top drive & agitator assembly for small version of Planetary Mixers.

Flame proof control panel as optional.

Spare bowl is provided so that maximum production can be achieved without losing production time. Thus the maximum utilisation of the basic machine for the regular production.

Available in Standard/GMP/cGMP/GAMP/GLP/ GCP & Lab Models.

The unit is used for blending the most delicate & fragile free flow products like powder or granules in 10 to 20 minutes. It is also the best way to mix very heavy & abrasive products the range of products includes colour, plastics, flour, drugs, pharmaceuticals, metal powders, mineral, fibers & many other.

It is revolved end over end, moving the products in & out of the constructed octagonal areas. This causes multiple folding action that ensures a through intermeshing of all the ingredients in the batch.

The result is a homogeneous blend regardless of particle size distribution, particle shape or density with a great efficiency.

Material of construction for contact parts in AISI 304/304L.

Octagonal shape body with rectangular top frustum & conical bottom discharge nozzle.

Piped baffles provided to reduce mixing time & to avoid dead spot.

Cleaning in place (CIP) nozzle provided for GMP / cGMP cleaning.

Charging & discharging through butterfly or IRIS type diaphragm valve or knife gate vale through manually of pneumatically operated system.

Safety Features: (i) Guards for drive parts. (ii) Limit switch for safety pipe guard.

Manual or electrical inching facility provided.

Bin charging system with Trolley provided.

Less energy consumption.

Hygienic design-smooth interior for GMP / cGMP cleaning.

Short cycle times.

In-line helical gear drive provided for better efficiency for power consumption.

CAPACITY AVAILABLE : 25 LTRS TO 3000 LTRS

Vibro sifters are used for raw material sieving in pharmaceutical, food & chemical industry. Raw material is fed through in feed hopper & there is a sieve of required mesh size through which the sieved material falls. There is Vibro motor & spring type suspension system through which the vibration the Vibro motor are transmitted to the sieve chamber. As the vibrates the material gets shifted or sieve through it.

Simplified design & construction which is trouble shooting maintenance free.

All contact part are from S.S. 316 & rest from S.S. 304.

for dust free system, gaskets can be used at in feed mouth & at the out let mouth of this shifter.

Vibro motor gives trouble free performance for much longer time & so it is better than mechanical sifters.

Removal of sieve is very easy as there are user friendly clamps for change of sieve for vhamber.

Ease of cleaning.

Castor wheel which are PU coated with S.S. brackets & thrust bearing ensure eaye movement of Vibro sift in the production area.

Ideal for mixing dry & wet material.

Paddle type blades so arranged on the shaft to give through uniform mixing of thick heavy material.

The drive system is through a suitable worm & motofr. ( TEFC FLAMEPROOF)

Provision for tilting arrangement, reversible switch & safety lock- switch to stop the mixer as soon as the cover is opened.

PTFE gland mechanism provided at shaft ends to prevent outside lubricants form entering in to the mixing chamber & to prevent inner leakage.

Bottom discharge silde regulated through butterfly valve of suitable diameter. 

available size - 50 ltr to 550 ltr ( 25 kg to 250 k)

MOC s.s. 304 / 316 / 316L.

CGMP model with documentation ( IQ, DQ, PQ, OQ ) as option

COMMUNUTING MILL

Communuting mill is used for downsizing of granules or for size reduction. It has large application in pharmaceutical, chemical & food industry. Machine has one rotor with knife edges which rotate on horizontal axis. There is one half round sieve mounted at the bottom of the rotor/ blade. Material is changed from the top through in feed hopper & material falls on the rotor blades. Due to the knife edges mounted on rotor, the downsizing of particle take place & through sieve material gets pushed outward from the bottom opening. Knife edges can be removed for cleaning very easily.

Simplified designed & construction which is maintenance free.

All contact part are from S.S 316 & rest from S.S 304.

For dust free system, gaskets can be used at in feed mouth & at the outlet mouth of the shifter.

High through put obtained due to impact force of rotating blades.

Easy of cleaning.

Castor wheel which are PU coated with S.S brackets & thrust bearing ensures easy movement of mill in the production area.