Tablet Press Control System works on compression force based press control system that utilizes feedback of measured compression peak force value applied on each tablet to continuously adjust die fill level and thus compression force. It establishes and maintains target compression force feedback control scheme. The press control system automatically rejects tablets that fall outside of the designated compression force limits.

Other than this it also allows other automated functions like

Auto lubrication pump system,
Hydraulic pressure control system
Safety Guards interlock systems
Critical Alarm logging with real time stamping like…

Emergency Pressed
Pneumatic Air Pressure down
Motors overload alarms
Die fill limit exceed alarms
Punch proxy disturbed alarm
Revolution proxy disturbed alarm
Powder level low alarm
Hydraulic oil level low alarm
Hydraulic oil temp. Over-shoot alarm

 1Noiseless, Maintenance free & high speed.

2.Portable and compact.

3.Electric power requirement less than other machine of the kind in the industries & lower energy consumption compared to reciprocating vibratory system.

4.All contact parts and screen of SS 304 AISI stainless steel material.

5.SS 316 quality contact parts optional.

6.Easy dismantling and cleaning facility for contact parts.

1.Hand wheel provided.

2.Separate centre pillar of Meehanite grade casting.

3.Turret of SG IRON 400/12 grade casting.

4.Very rigid gunmetal feed frame with sufficient height to avoid spill over of powder.

5.Feed frame setting time is very less compared to other make machine..

6.Central oil lubrication system with hand pump.

7.Oil groove on top face of turret for collection of excess oil.

.1Design as per GMP norms.

2.Tabletop Model.

3.Easy to operate and clean.

4.Centre Driven with fixed pulley & ACVE.

5.Turret with keyway in upper guides.

6.Open fixed feed frame.

7.Hard heat-treated rollers.

8.Drive from center pillar by worm reduction gearbox.

9.Turret fitted at bottom with thrust bearing & upper with taper roller bearing.

10.Tablet parameters controls outside. (Optional)

11.Option of “D”, “B” and Multi tooling.

1.Hand wheel provided.

2.Re-designed variable speed pulley.

3.Separate centre pillar of Meehanite grade casting.

4.Turret of SG IRON 400/12 grade casting.

5.Very rigid gunmetal feed frame with sufficient height to avoid spill over of powder.

6.Feed frame setting time is very less compared to other make machine.

7.Central oil lubrication system with hand pump.

8.Oil groove on top face of turret for collection of excess oil.

9.Optional equipment like Dust Extractor and De-burring & De-dusting Unit can be attached with the machine.

.

1Solid C. I. Body (Equivalent to Manesty Press body).

2.Inching system provided.

3.Phosphor bronze bush provided inside the turret hole.

4.Imported niddle roller bearing provided at the bottom of turret.

5.Reverse direction motion protection is provided to avoid major accident.

6.Lower punch lubrication provided.

7.Aluminum covers for rotor teeth.

8.Fly over on upper punch is provided.

9.Friction plate is provided on cam plate to minimize wear & tear of cam track, which also facilitates its easy replacement.

10.Higher turret speed 15 to 42 RPM gives higher output than standard machine.

1Available in cG.M.P. Model.
2. AC variable frequency drive for main motor.
3. Built in facility of Pre-Compression.
4. Force Feeding System with ACVF.
5. Gravity feeding also provided with the machine.
6. Outside controls for tablet parameters weight and Hardness.
7. Lower punch seal is provided.
8. Auto lubrication system.
9. Upper punch lubrication with separate oil cup.
10. Digital Counter for Tablet Output, Rate of Production & Turret RPM.
11. Contact parts i.e. hopper, discharge chute & dust extractor nozzle are S.S 316.
12. Adjustable upper punch penetration.
13. Guard with interlock – with transparent Acrylic frameless guards.
14. Inching system for machine.
15. Reverse direction motion protection is provided to avoid major accident.
16. Antivibration mounting provided Hence no foundation required.

1. Available in cG.M.P. Model.
2. AC variable frequency drive for main motor.
3. Gravity feeding provided with the machine.
4. Outside controls for tablet parameters weight and Hardness.
5. Lower punch seal is provided.
6. Auto lubrication system.
7. Upper punch lubrication with separate oil cup.
8. Digital Counter for Tablet Output, Rate of Production & Turret RPM.
9. Contact parts i.e. hopper, discharge chute & dust extractor nozzles are S.S 316.
10. Adjustable upper punch penetration.
11. Guard with interlock- with transparent Acrylic frameless guards.
12. Inching system for machine.
13. Reverse direction motion protection is provided to avoid major accident.
14. Antivibration mounting provided Hence no foundation required.
15. Higher turret speed maximum 50 RPM gives output than standard machine.

1.Robust and durable.

2.Efficient  dependable.

3.Very compact design.

4.Continuous oscillating stirrers drive.

5.Easy to clean. Entire working zone and stirrer can be dismantled quickly without using spanners

.6.Simple screen holding and tensioning device.

7.Availability of different mesh size of screen.

8.Long life and economic cost of screen.

1. Provided with stainless steel SS 304 contact parts.
2. Blower fan is dynamically balanced and the unit is with castor wheels.
3. Overcome dust hazards as well as cross contamination at tablet compression.
4. Minimises mechanical strain, excessive wear of tableting machine-resulting in minimum machine break-downs  and punch wears.
5. All inlet manifolds and dust collection tray are of S.S.
6. Four inlet manifolds facilitate to connect Cip Press Machine and the De-dusting units.

1.Noiseless & Maintenance free unit.

2.Electric power requirement less then other machines of the kind.

3.Height adjustment facility provided with the unit to suit with any Rotary Tableting Machine.

4.All contact parts made of stainless steel and components can be easily washed and/or sterilized.

5.Tablet conveying route is so geometrically designed for imingement of tablets on their burrs, which can break easily.

6.Efficient De-Burring & De-Dusting and full suction output is concentrated on De-Dusting zone for flushing out powder.

Since 1987 Cip has laid the foundation of its reputation as a manufacturer of exceptional, healthy, reliable machinery and tooling with a global base. Also there has been major investment in technical and validation support services to enable us provide unrivalled service to our customers.

Our enthusiastic team of expert engineers and customer service group offer a prompt reply and quick delivery.

Our wealth of experience in Tableting means that we can always offer effective solutions to meet customer requirements and solve your production problems.

Cipweka has carved its niche as versatile all purpose equipments for research and development in pharmaceuticals, chemical, cosmetic and food industries. Cipweka broad-based functions providing an edge for companies specializing in R & D.

Based on powerful main drive to be selected from:

01. Horizontal Drive.
02. Vertical Drive.

1. All contact parts are made out of S. S. 304 (S.S.316 on demand at extra charges).
2. Coupling provided between motor shaft and rotor shaft for ease in maintenance.
3. Three oil seals between the motor and the processing chamber to prevent liquid going in the motor winding, resulting in the burning of the motor.
4. Modified design of semi concave teeth in rotor and stator reduced motor HP and gives better performance in size reduction without damaging the product.
5. Extended bearing housing specially designed to facilitate fine adjustments of bearing clearances or backlash to avoid metal to metal contact of rotor and stator. This unique design provides smooth and consistence all round performance and long life of rotor and stator.
6. Leak proof neoprene sealing device.
7. Three-way cock for draining and recirculation of liquids provided as standard. Extra discharge spout provided as a standard for viscous products.
8. DOL starter with overload relay for protection against single phasing and low voltages.
9. Contact parts can be easily dismantled for cleaning.
10. Special design facilitates adjustment of grinding gap by an exterior screw by means of handle even during operation.
11. Flameproof motor and flameproof rotary switch can be provided on request at extra cost.

1.All contact parts are made out of S. S. 304 (S.S.316 on demand at extra charges). No casting are used for avoiding contamination problems.

2.Coupling provided between motor shaft and rotor shaft for ease in maintenance.

3.Three oil seals between the motor and the processing chamber to prevent liquid going in the motor winding, resulting in the burning of the motor.

4.Modified design of semi concave teeth in rotor and stator reduced motor HP and gives better performance in size reduction without damaging the product.

5.Extended bearing housing specially designed to facilitate fine adjustments of bearing clearances or backlash to avoid metal to metal contact of rotor and stator. This unique design provides smooth and consistence all round performance and long life of rotor and stator.

6.Leak proof neoprene sealing device.

7.Three-way cock for draining and recirculation of liquids provided as standard. Extra discharge spout provided as a standard for viscous products.

8.DOL starter with overload relay for protection against single phasing and low voltages.

9.Contact parts can be easily dismantled for cleaning.

10.Special design facilitates adjustment of grinding gap by an exterior screw by means of handle even during operation.

1.Compact portable model, which can be used for regular production as well as in R & D dept.

2.Can be used in liquid, tablet, injectable dept.

3.Can be used on plastic, aluminum, pet containers etc.

4.Change over time – 10 minutes maximum.

5.Maintenance free.

6.Immediate pay back saving in manpower.

7.Entire labeling area is covered with uniform gum application with minimum gum consumption.

8.Applications: Pharmaceuticals, Chemicals, Cosmetic, Food & Beverage & many more.

9.Note: In some cases 100% labels may not be sicked on bottle circumference because of label grammage and for lightweight bottles containers.

1.All the contact parts SS 304.

2.Thrust bearings are provided to carry rigid and thrust load.

3.Easy for cleaning and operating.

4.Plastic dust cover provided for apparently seeing the mixing process.

5.Interlocking system at plastic dust cover is provided to avoid the accident.

6.The tilting device provided to ease the unloading of the material.

7.Provision is made for lubricating all moving parts and specially designed to prevent oil coming in contact with powder.

1.G.M.P. point of view machine is provided with S. S. cladding on base, S. S. belt guards, S. S. cover on motor. No exposed painted surface on top of the machine. Motor rails, screw and guide rods are chrome plated.

2.Beaters assembly bearings are in a separate pillow blocks for ease in maintenance.

3.Very less down time as only beaters assembly will have to be reversed (and not the complete chamber) for making it knife to impact forward or vice-versa which can be done by single operator.

4.Fixed beaters assembly is provided as a standard supply which increase the output by 10% to 30% reduce noise level and also ease to clean asthere are no cavities. (If product demands, swing beaters assembly can be provided.)

5.Beaters and shaft are of stainless steel 410 quality and beaters are further hardened and chrome plated. Beaters are fitted on a splined shaft.

6.Transmission of heat to the chamber from bearings is minimum as they are away in separate pillow blocks. This facilitates to some extent in processing of heat sensitive products.

7.Beaters assembly is dynamically balanced which reduce vibration and noise level and increases bearings life.

8.Castors provided for mobility and breaks can be applied for fixing machine at one place.

9.Machine is available in plain or water-jacketed models. Flame proof electricals can be provided on demand at extra cost.

1.Useful for precision grinding of ointments, paints, inks etc.

2.Hard chrome plated rollers made from special alloy steel.

3.Calibrated hand wheels provide to adjust gaps between the rollers.

4.Safety device provided to avoid close friction of the rollers.

5.Provision of emergency stop switch.

6.Scraper fitted to prevent leakage or waste.

7.Provision of SS tray below the rollers.

1.Coating Pan is made of SS 304.

2.Totally enclosed with M.S. cladding with standard gearbox, motor, and hot air blowing arrangement.

3.Designed with M.S. fabricated structure.

4.Mounted on dynamounts, this avoids foundation.

5.30″, 36″, 42″ or 48″ Coating Machine has variable speed drive and hot air blowing system in built in the machine.

6.60″ or 72″ Coating Machine has two speeds with step pulley without hot air blowing system.

1.Direction of beaters can be changed by reversible switch.

2.All contact parts can be easily and quickly dismantled and cleaned.

3.Machine is designed for continuous operation.

4.Cylindrical screen for higher output.

5.Castor wheels provided for mobility.

6.Flameproof electrical components can be provided at extra cost.

7.Beaters and scraper blades of S.S. 304 quality.

8.S. S. Perforated Screens:
0.5, 1.0, 1.5 mm Hole Dia.
2, 3, 4, 5, 6 mm Hole Dia.
7, 8, 10, 15, 20, 25 mm Hole Dia.

9.S. S. Wire Mesh Sieve:
4, 6, 8, 10, 12, 14, 16, 20, 24, 30, 40, 50, 40, 50, 60 Mesh.
80, 100 Mesh.

1. Product kept in the hopper slides down to the enclosed chamber, where it is milled in between beaters and screen to the required mesh/micron size which can be collected at the bottom in the container.
2. Quality and output depends upon the three main variables.
3. Beaters shape. (knife/impact forward)
4. Speed.
5. Screen size.
6. Knife edge for coarse or large particles and impact or flat edge for finer particles. High speed for fine grinding, low speed for coarser particles. A wide range of screen is available for various process needs.

1.Direction of beaters can be changed by reversible switch.

2.All contact parts can be easily and quickly dismantled and cleaned.

3.Machine is designed for continuous operation.

4.Cylindrical screen for higher output.

5.Castor wheels provided for mobility.

6.Flameproof electrical components can be provided at extra cost.

7.Beaters and scraper blades of S.S. 304 quality.

8.S. S. Perforated Screens:
0.5, 1.0, 1.5 mm Hole Dia.
2, 3, 4, 5, 6 mm Hole Dia.
7, 8, 10, 15, 20, 25 mm Hole Dia.

9.S. S. Wire Mesh Sieve:
4, 6, 8, 10, 12, 14, 16, 20, 24, 30, 40, 50, 40, 50, 60 Mesh.
80, 100 Mesh.

1.Robust and durable.

2.Efficient and dependable.

3.Quiet in operation.

4.Continuous oscillating stirrers drive.

5.Easy to clean. Entire working zone and stirrer can be dismantled quickly without using spanners.

6. Simple screen holding and tensioning device.
7. Availability of different mesh size of screen.
8. Long life and economic cost of screen.

1.Noiseless, Maintenance free & high speed.

2.screening diameter of 750 mm.

3.Portable and compact.

4.Electric power requirement less than other machine of the kind in the industries & lower energy consumption compared to reciprocating vibratory system.

5.Standard machine are with TEFC motor explosion proof / flame proof motor material.

6.All contact parts and screen of SS 304 AISI stainless steel material.

7.SS 316 quality contact parts optional.

8.Special requirement like brushing arrangements, SS lid with charging port and spring loaded outlets.9.

Easy dismantling and cleaning facility for contact parts.

10.Wide range of screen sizes 4-300 Mesh.

11.Double & Triple deck screens with outlet and hopper for bottom deck available on request.